Jump to content

Search the Community

Showing results for tags 'urix'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • General Mobile Radio Service (GMRS)
    • Guest Forum
    • General Discussion
    • Technical Discussion
    • Equipment Reviews
    • FCC Rules Discussion
    • myGMRS.com
    • National and Regional GMRS Nets
  • Other Radio Services
    • Family Radio Service (FRS)
    • Multi-Use Radio Service (MURS)
    • Amateur Radio (Ham)
    • 900 MHz License-Free Radios (ISM)
    • Meshtastic and Reticulum
  • Off-Topic
    • Miscellaneous Topics
  • TreasurecoastGMRSclub's Radio Etiuette
  • TreasurecoastGMRSclub's Radio gear
  • South Western PA GMRS's Repeaters
  • South Western PA GMRS's Welcome New Members
  • South Western PA GMRS's Repeater System
  • South Georgia GMRS's SOUTH GEORGIA GMRS REPEATER STATUS
  • South Georgia GMRS's SOUTH GEORGIA GMRS NEWS
  • WV/OH GMRS's Repeater Pulled from Tower
  • NOVA GMRS's Area Repeaters
  • NOVA GMRS's MEET UPS / EVENTS
  • NOVA GMRS's General Conversations Related to NOVA GMRS
  • DELMARVA GMRS's Repeaters
  • DELMARVA GMRS's Events
  • ISLACOMM GMRS's Topics
  • ISLACOMM GMRS's Topics
  • Maryland GMRS Network's Topics
  • Maryland GMRS Network's Topics
  • Alaska GMRS's Welcome!
  • Southwest Virginia GMRS's Topics
  • Ozark Plateau GMRS's Discussions
  • Moline, IL QC Area GMRS's Clubs Around QC
  • Moline, IL QC Area GMRS's Topics
  • NORTH CAROLINA GMRS (GMRS Outlaws Extension)'s Repeater Listings
  • NORTH CAROLINA GMRS (GMRS Outlaws Extension)'s Repeaters and simplex listings
  • GMRS Outlaws's Net Check-in
  • GMRS Outlaws's Repeaters
  • CLAARC GMRS's Moderators and Admins
  • Mississippi GMRS Communications's Club Announcements
  • Mississippi GMRS Communications's Club Repeaters
  • BROADNET GMRS REPEATER SYSTEMS's Topics thank you
  • The Mesa Crest Repeater Club's TMCRC Repeaters Estimated Coverage
  • West Michigan GMRS's Guides & Discussion
  • Chicagoland GMRS's Discussions
  • Central Florida GMRS's Topics
  • Missouri GMRS's Topics
  • Vista Woods GMRS's Topics
  • South Central Tennessee GMRS's New Member Info

Calendars

  • Community Calendar
  • ISLACOMM GMRS's Events
  • Southdade GMRS Club's Events
  • Southwest Virginia GMRS's Events
  • Moline, IL QC Area GMRS's Events
  • Mississippi GMRS Communications's Classes and Events
  • PRCC Inc / WP 444 GMRS Net's Aguada GMRS Net on 444 ATA repeater
  • The New Horizons's Events
  • Chicagoland GMRS's Events Calendar

Categories

  • Two-Way Radios
  • Repeaters
  • Antennas
  • Computers
  • Misc. Electronics
  • Chicagoland GMRS's Adverts

Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Joined

  • Start

    End


Group


Website URL


Skype


Slack


Name


Unit Number

 
or  

Location


Interests

Found 3 results

  1. I have a Motorola MTR 2000 repeater. I have an ICS Controller board in the J5 system connector, going to a URIxB via the DB-9 to DB-25, assembled by me. I've done days worth of research to no avail. The repeater & URI both show TX if I key the radio in the simple_usb_tune menu. Hitting the repeater with a HT, RX lights up but no TX on the URI or MTR. Not sure if this is RSS programming or on the URI/Asterisk side. Any suggestions would be greatly appreciated. Thank you all!
  2. Lets start out with my setup so this might not work for you. My repeater is a Bridgecom BCR-40DU, I purchased the URIx, 25 pin cable, and Micro SD from the myGMRS store. Make sure your not using a Raspberry Pi 4, trust me it doesn't work. I ended up getting a Raspberry Pi 3B+. After installing the micro sd card into the pi make sure you connect an ethernet cable, log in, change password like instructed, then set up wifi if you want by following instructions in the quick start guide that came with the micro sd card, don't forget to log into your router and set up port forwarding. Your gonna wanna go into your simpleusb.conf file and change a few things. sudo nano /etc/asterisk/simpleusb.conf carrierfrom = usbinvert ; no,usb,usbinvert ; no - no carrier detection at all ; usb - from the COR line on the USB sound fob (Active high) ; usbinvert - from the inverted COR line on the USB sound fob (Active low) ctcssfrom = usb ; no,usb,usbinvert ; no - CTCSS decoding, system will be carrier squelch ; usb - CTCSS decoding using input from USB sound fob (Active high) ; usbinvert - from the inverted CTCSS line on the USB sound fob (Active low) duplex = 1 ; Duplex 0,1 ; 0 - half duplex ; 1 - full duplex When your done making the changes hit ctrl + o followed by enter then ctrl + x followed by enter. I wasn't able to use DTMF tones to connect to different nodes so I found a command in one of the forum pages to connect through ssh. sudo asterisk -rx "rpt fun 24219 *3172" 24219 is my node so insert your node number, *3172 will connect me to node 172, *3xxxxx will connect you to your node of choice, xxxxx being the node number. If your gonna use the Pi as your repeater controller then your gonna have to modify your rpt.conf file. sudo nano /etc/asterisk/rpt.conf hangtime = 1000 ; squelch tail hang time (in ms) (optional, default 5 seconds, 5000 ms) althangtime = 2000 ; longer squelch tail totime = 180000 ; transmit time-out time (in ms) (optional, default 3 minutes 180000 ms) idrecording = |ixxxxxxx ; cording or morse string see http://ohnosec.org/drupal/node/87 ;idtalkover = |ixxxxxxx ; Talkover ID (optional) default is none see http://ohnosec.org/drupal/node/129 ; See Telemetry section Example: idrecording = rpt/nodenames/24219 idtime = 900000 When your done making the changes hit ctrl + o followed by enter then ctrl + x followed by enter. Change the xxxxxxx to your callsign make sure you keep the |i or it won't identify. After your done making all the changes make sure to restart asterisk by using: sudo service asterisk restart These are all the changes I did to make everything work with my system. Once I get voice ID working I'll do an update. I hope this helps someone. It took me quite a few days of playing around trying to figure this out. Joe WROE856
  3. I'm setting up my node on the GMRS Network and I'm having a little difficulty. I have a Bridgecom BCR 40DU repeater. I know that I have connected everything correctly because my node shows up on the GMRS map and I'm able to connect to other nodes. I can hear traffic from other nodes and it transmits through my repeater. The issues I'm having is I cannot transmit. When I try transmitting, I notice the TX light doesn't illuminate on the URIx. Any help would be greatly appreciated. Thank you Tim WROE916 BCR-40U_BCR-50V_BCR-220_Owner_s_Manual_Ver_1.7.pdf URIx Data Sheet.pdf
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use and Guidelines.