Jump to content

ID-O-Matic IV


RCM

Recommended Posts

I just put together a controller kit yesterday, the ID-O-Matic IV from Ham Gadgets: http://www.hamgadgets.com/id-o-matic-iv

From the name it sounds like just an IDer, but it actually can control a repeater. It has a lot of features for the low price, and is in my opinion all I really need or can use for a GMRS repeater. Works pretty well as a ham repeater too, in fact.

 

You can get this controller already assembled for about $60, but I elected to save $20 by assembling it myself. It's been awhile since I put together a kit anyway, and that's part of the radio hobby for me.

 

It shipped quickly and wasn't missing any parts. It doesn't include a hard copy of the manual; you have to download a pdf from the website. I had already done so in preparation. It went together with no issues, and no magic smoke escaped when I powered it up to test.

 

I haven't tested it with the radios yet. First I have to figure out the programming, which is done via usb with a terminal emulator program. I also have to interface to the radios, which shouldn't be too difficult.

Link to comment
Share on other sites

So I finally got around to programming my controller today, and it went off without a hitch. I set it up for Morse ID and an EOT tone (Morse "K"). Most GMRS repeaters I've heard have nothing except a squelch tail, but that's not how I want to do mine.

The RF chores will be handled by a pair of Kenwood TK-805Ds.

Link to comment
Share on other sites

  • 2 weeks later...

The ID-O-Matic may be a great product. But, HamGadget's customer service leaves a bit to be desired.  

All orders are shipped via US Postal Service. I normally ship every day. Please bear in mind, however, that from time to time there may be an extra few days delay in shipping.

I ordered one on Dec 11 and received immediate order acknowledgement. However, on the 14th I had still heard nothing about shipping. So, I wrote them to ask when it might ship. Again, quick response saying it had been stamped and addressed and would be posted on the 15th. Today, the 16th, the USPS stall does not have the package in their hands. 

Link to comment
Share on other sites

The ID-O-Matic may be a great product. But, HamGadget's customer service leaves a bit to be desired.  

All orders are shipped via US Postal Service. I normally ship every day. Please bear in mind, however, that from time to time there may be an extra few days delay in shipping.

I ordered one on Dec 11 and received immediate order acknowledgement. However, on the 14th I had still heard nothing about shipping. So, I wrote them to ask when it might ship. Again, quick response saying it had been stamped and addressed and would be posted on the 15th. Today, the 16th, the USPS stall does not have the package in their hands. 

You do realize this is the busiest week of the year for USPS, right? I wouldn't assume the problem is with Hamgadget just because USPS can't provide tracking info yet.

Link to comment
Share on other sites

The ID-O-Matic may be a great product. But, HamGadget's customer service leaves a bit to be desired.  

All orders are shipped via US Postal Service. I normally ship every day. Please bear in mind, however, that from time to time there may be an extra few days delay in shipping.

I ordered one on Dec 11 and received immediate order acknowledgement. However, on the 14th I had still heard nothing about shipping. So, I wrote them to ask when it might ship. Again, quick response saying it had been stamped and addressed and would be posted on the 15th. Today, the 16th, the USPS stall does not have the package in their hands. 

 

Not only is this the busiest time of year for the postal service, it is a busy time for most people as well.  Keep in mind that the HamGadgets company is actually only one man, and he has a lot going on.  Dan Magro, W7RF, is the ARRL Technical Specialist for the Colorado Section, the Rocky Mountain DX club President, as well as NCARC, WARC, past President.  He's also a 6-meter band fanatic, and with all of the recent aurora activity, he is probably banging out Morse code DX contacts on 50.125MHz.

 

If you order a kit, he is the guy who counts all the parts, bags them up, and ships them.  If you ordered a product assembled and tested, he is the one who solders it together, and tests it. ...then re-packages it for shipping.  I've never had bad service from the guy, but I can see how he might get behind schedule a bit.

Link to comment
Share on other sites

My comment was about customer service, not quality. Of course I realize it is the holiday season. USPS has already provided tracking info, the label was printed. However, the package still has not been tendered to them. Scanning in a Priority Mail package is not an option, all such parcels are scanned, regardless of the post office load.

 

I also assumed it was a one-man business. However, I would also assume it would be a well managed business and that means not preparing product as needed, but maintaining a small stock of products that are ready to be shipped when ordered. As to his ham activities... really? If you want to go into business you have to prioritize your life. If you value your hobby over your customers, then expect to get customer comments like mine. (And don't even start with the ARRL). If you order a new fishing rod online for your trip to Idaho and it arrives too late because there was a bass run at the rod vendor's location, would you accept that?

 

My point was, and is, I have no doubt about the quality of W7RF's products, that's why I ordered the controller in the first place. However, I also think people might want to know exactly the type of things other commenters have pointed out, especially if time is an issue.

 

BTW, for anyone in the market for a controller, you might want take a look at this review list from Ham.Net. (Note: the ID-O-Matic clearly comes out on top in a price/feature/quality comparison)

Link to comment
Share on other sites

  • 2 weeks later...

I finally received my ID-O-Matic. It was delivered Late Saturday, but I couldn't pick it up until yesterday. Those who commented about postal delays were right. But, of course that was all the more reason to be prompt about mailing it in the first place.

 

I ordered the controller and box hoping to get a nice fitting installation.  The controller itself is fine. I used a Mac to set it up (OS 10.14.2) and had no issues whatsoever (well, other than grabbing a faulty usb cable from my cable bin). My only minor gripe is that 20 years into the second millennium, something like this really ought to have a built-in web server for setup (and Wi-Fi or ethernet onboard).  That would also make it easier for post install changes.

 

However, I do have some serious reservations about the box.  #1, the only way the board will fit into the box makes it impossible to have the USB plug connected and difficult to access the wire connectors. Also, although the board is drilled for hold-down bolts, there are no matching studs in the box.  Basically, it is just a standard project box that is ill sized for the board it will contain, at about 5 times the price I can get it on Amazon or the local electronics shop (Yes, we still have one.)  

 

My advice: Since you'll have to drill holes in the box anyway, you might as well save the money and get a box that fits your individual needs somewhere else. OTOH, the ID-O-Matic is a nice piece of kit, especially at the price they sell it for.

Link to comment
Share on other sites

Well.  I got the ID-O-Matic setup and running on a Motorola MTR2000. In fact, the only reason we needed the ID-O-Matic was for a "Roger Beep" that some users felt was necessary.  Anyway, it works fine but I had noticed one minor issue, so I emailed Dan...

 

I have the controller hooked up and generally working.  However, I have one issue. After receiving COR, turning on PTT, losing COR and then dropping PTT (I.e. a normal transmission) the LED remains blinking green and never returns to solid green.  Everything seems to operate correctly, it is just the LED that is an issue.
 

 

And, here is his reply.

 

I never even pay any attention to the LED so I cannot even tell you what the manual will tell you about it.

 

I USE the controller and never care what flashy lights mean unless there is a problem.

 

If you want to know more about the LED, read the manual.


There are so many parameters to change and it is a waste of time trying to chase down what you MAY have programmed to make the LED operate as you describe.

 

If you want to see the LED operate the way the manual states or if something you may have programmed is not right but you cannot figure it out then do a reset, of course all of your programming is reset to factory, but the LED will be just as the manual describes.

 

Use the controller, if it operates the way you want, leave it alone.

73, Dan Magro W7RF

 

Seriously, RTFM? Is this the kind of customer response he normally provides.   First he says he never read his own manual about the LED. Then, he says I should read the manual.  In fact, he just bought the company in 2017 and it is likely he actually does know nothing about the operation (and peculiarities) of the ID-O-Matic.

 

Summary: If all you want is to tie two radios together with an ID and Roger Beep, the ID-O-Matic will work fine. But, you should know it does essentially no audio (PL/DPL, etc.) processing, logging etc.  Also, as demonstrated above, you probably shouldn't hold out high hopes of support if you have any problems.

Link to comment
Share on other sites

The reason it keeps flashing is because it is in timing mode. After the timer expires (10 or 15 minutes; whatever you programmed it for) it IDs again and then the LED returns to solid. Exactly as it says in the manual.

 

I give Dan two thumbs up and will continue to support him and his products.

Link to comment
Share on other sites

I give Dan two thumbs up and will continue to support him and his products.

Perhaps you could get Dan to read "How to Win Friends and Influence People" beacause he's not doing anybody any favors, especially himself, with emails like that. biggrin.png

http://en.wikipedia.org/wiki/How_to_Win_Friends_and_Influence_People

Link to comment
Share on other sites

The reason it keeps flashing is because it is in timing mode. After the timer expires (10 or 15 minutes; whatever you programmed it for) it IDs again and then the LED returns to solid. Exactly as it says in the manual.

I eventually came to this conclusion as well. The manual says the flashing LED means it is in a timing cycle. Which cycle it is, is not specifically mentioned and it sure wouldn’t have killed him to answer my question. That’s ok. I got the message, my business is not appreciated and I should, and will, shop elsewhere next time.
Link to comment
Share on other sites

Since this topic was posted in the Equipment Reviews forum, I guess a review of the product itself (as opposed to sales and service issues) is appropriate.

 

The ID-O-Matic is a very basic station ID and repeater controller offering a minimal set of functions including:

  • Automatic periodic ID in CW and optionally, with an extra module, voice.
  • An optional "Courtesy (Roger) Beep" when the incoming carrier is dropped.
    • ​The "beep" consists of one or more characters sent in audible morse code.
    • A separate "beep" is available for input timeouts.
  • The speed, volume, and pitch of the beep and ID are controllable
  • Timing controls for maximum talk-time (PTT) hang time, ID time, etc.
  • Option for one alternate ID message (based on the state (high or low) on an input line.
  • Beacon control functionality.
  • An option to control an external fan.
  • Programming is via a terminal connection over USB using a simple menu based system.

The following common repeater control functions are not available:

  • Other than a gain control, there is no processing of audio.
  • There is no processing of CTCSS (PL, DPL, etc.).
    • This means any use of CTCSS on Rx or Tx must be done in the radios themselves.
  • There is no provision to trigger an ID with an external signal.
  • There is no provision to have an alternate "beep" or "beeps." (For example, when on battery power.)
    • Note, while sales material states it is possible to have an alternate "beep," such an option does not appear in the programming menu and is not documented in the manual.
  • There is no logging.
  • Other than for backup power, it is specifically not recommended to configure the controller or to even leave the USB control line connected during operation. This means you should not plan on being able to alter the program remotely. However, In practice leaving the controller connected to a PC during operation does not seem to exhibit any problems, as long as you take care to Quit the programming menu after use.

For the price, for a very basic repeater system, this probably cannot be beat. However, do consider the design, documentation and firmware are now 5 years old and the original developer Dale, N0XAS, is no longer with the company having sold it to the current owner, Dan, W7RF in 2017. As noted in posts above, this change may impact the level and quality of support available.

Link to comment
Share on other sites

Thanks for the review, berkinet. I have a couple of questions if you might be able to answer...

 

Is the variable pitch for beeps and ID for the individual ID & beep or is it a one-for-all setting?

Is the voice module something that records a voice or is it a computer generated voice?

 

I know that I might be able to google some of this but since you have the unit and did the review, I figured I would ask.

Link to comment
Share on other sites

...Is the variable pitch for beeps and ID for the individual ID & beep or is it a one-for-all setting?

 

Each setting, Courtesy Beep and ID  has it's own pitch setting (in Hertz).

 

 

...Is the voice module something that records a voice or is it a computer generated voice?

 

From the product page (I don't own one):  This board will record and play back a 10-second voice message.

Link to comment
Share on other sites

The voice message is often used to make periodic announcements of upcoming events, such as club meetings, special events, and so forth.

 

Alternatively, it can be used to replace a morse id such as "This is the W9LJ VHF repeater" or "You are listening to the N9IAA repeater" both of which are real announcements currently being used.

Link to comment
Share on other sites

I built mine as a very basic controller, without the voice ID. That can be added later, if I decide I want it. But it works perfectly for what it is. It was also delivered quickly, all the parts were there, documentation was thorough and it went together without difficulty. It was also easy to program.

 

Most GMRS repeaters that I have heard don't even have ID nor an EOT indicator. Some don't even have a squelch tail. It can be hard to tell if you are even getting into the repeater, or if a listed repeater even actually exists in real life. I have mine programmed to ID (in Morse code) after the first transmission and (if and as long as there are subsequent transmissions) every 15 minutes until the activity is over. I also have it set to beacon every hour. This is to announce its presence to GMRS operators who might be traveling through the area. Another advantage of the beacon mode is it allows me to listen for it when I am out and about, as an aid in gauging its coverage.

 

The ID-O-Matic adds these features to my repeater, and makes interconnection between the receiver and transmitter used in the repeater, for less than $50 shipped. Sure you can get a controller with more features. They start at about $200 and go up rapidly. $300+ is more common for controllers that have more features than the ID-O-Matic offers.

But the radios I'm using as receiver and transmitter have PL built in, so I don't need that built into the controller. My repeater is easy for me to access, so I don't need to be able to control it remotely. Nor do I have any need nor desire to have a computer powered up and connected to it 24/7.

 

This little controller does everything I need it to do, and does it at a price that is not much more than those Chinese controller boxes that connect a pair of BF-888s or whatever and use VOX to control the transmit. And it's a much more serious controller than those. It's not a fair comparison to pick it apart based on the features found in a $300+ controller.

 

So that's my review. I give it thumbs up, and I'll probably buy at least one more of them.

Link to comment
Share on other sites

I just stumbled upon the Open Repeater Project. https://openrepeater.com.

 

This is a Raspberry-Pi based repeater controller that fits somewhere between the bare-bones ID-O-Matic and more "feature rich" controllers. Other than the cost of the Pi, it is free.  Control is via a built-in web server, so remote operation is available. There is a video available on the website that give a nice, though not particularly exciting, overview of the controller.

 

This is something I am likely to try, so I will report back.

 

BTW, having a Pi in your repeater setup is a nice idea anyway. Especially if you install the VirtualHere software (https://www.virtualhere.com)  which allows you to remotely connect to USB devices.  Like, for radio programming, etc.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use and Guidelines.