Jump to content

Swivel Clamp for mast ideas?


WQWI871

Recommended Posts

That's a loaded question. There are so many clamps, telescoping mast, poles, tripods and such and every situation is different, each operator has specific needs. I have a pile of clamps and hinges from dozens of experiments, is always nice to find the part you need when in the middle of tower work.  I found most of my stuff on fleabay and local marine hardware stores. most of the stuff in regular hardware is not advisable for antenna deployment unless it is Stainless steel. Do you have a local CB/HAM shop? not many left I know.

Link to comment
Share on other sites

I'm not familiar with any local cb or ham shops. The local flea and farmers market doesn't have any supplies, either. Usually I would need to fabricate something or find parts at a hardware shop or fleabay. If I can figure out how to upload images, I'll give some examples of what I'm looking for. Again, these are just examples. The mast is cylinder. Sometimes my biggest issue is simply knowing what the part is called. I didn't find out until some months ago that screw eyes / eye screws were called that. I knew what they were, but, had trouble finding them because I didn't technically know what they were called.

 

Edit: Giving more details, the antenna and mast is pretty light and the mast will be secured against the wall. But, 35' is still a bit annoying to push up. I wanted a clamp to attach to something, such as a pipe that will be cemented, and could simply push / walk the mast up into place while the clamp is basically holding the bottom of the mast down. It's a little difficult exploring options here with the hardware shop employees. A lot of them don't like giving individual help. The guy a couple days ago was rude and didn't seem interested, but, I think he only stuck around because another employee pulled him from his lunch break.

post-1363-0-46531500-1494263314_thumb.jpg

post-1363-0-13676500-1494263321_thumb.jpg

post-1363-0-94960800-1494263325_thumb.jpg

post-1363-0-35399500-1494263330_thumb.jpg

post-1363-0-75235300-1494263345_thumb.jpg

post-1363-0-90627900-1494263354_thumb.jpg

post-1363-0-68036500-1494263363_thumb.jpeg

post-1363-0-73905500-1494263372_thumb.jpg

Link to comment
Share on other sites

I would need to see pictures or drawings of your site to even give you an idea. defiantly not the flag pole holder. although I have used similar to hold antenna for temporary mobile set up. I like 1,2, 7, 8 of the first pictures. You just need to decide what will work and how much money you made of.

Link to comment
Share on other sites

I think the plumbing clamps might be fine if I can find the right size. One of those quick release levers that's on modern bicycles would be nice or wingnuts. The antenna and mast are pretty light, I can lift the entire concept up to put it up without a clamp, so, strength isn't too important. The mast will be secured as well. The idea of the clamp is just for quick convenient deployment up and down if I need to make changes. I can't find my old picture of the area, but, I can get another picture if It'll help. My budget is about $10.

 

Edit: I actually found one with quick levers. http://www.pssl.com/2-In-Wrap-Around-Clamp-With-Dual-Quick-Release-1

Are they called Scaffolding Clamps?

Link to comment
Share on other sites

The entire concept including antenna is roughly 10lb-15lb. It really is a simple light setup, so, I feel paying more for an actual tilt hinge is unnecessary. I was just looking for a small cheap clamp. Something from a hardware shop, or, alter something to use.

Link to comment
Share on other sites

  • 2 weeks later...

So, after dealing with a few unexpected issues by others' errors, the mast is up; 30'. I had to improvise for the moment with some hardware, such as the pvc sleeves due to errors, but, the hard part is over. I just have to swap stuff out when I'm ready.

 

 

 

http://i64.tinypic.com/2utpvm1.jpghttp://i64.tinypic.com/2ntvhva.jpg

Link to comment
Share on other sites

Funny lol. Yeah, I'm still upgrading some hardware such as bolts and guy wires and replacing and adding on coaxial cables and other antennas, so, I didn't want to waste my time putting my current antennas back up when I would be taking the mast down a few times. Maybe by the end of this month everything should be taken care of.

Link to comment
Share on other sites

Antennas up. Pretty much all is taken care of now. I plan on a few small "extra" steps in the near future, but, It's fine for now. The cable ties holding the coaxial you can see sticking out is temporary, just to keep the coaxials from swaying in the breeze. Guy wires are up, I used some aircraft galvanized wire rope. I'll do a little tidying up later.

 

 

 

 

http://i66.tinypic.com/1zd3exk.jpg

Link to comment
Share on other sites

I didn't want those antennas so close together, but, trying to improvise on a budget. That actually doesn't include the other three antennas lol. Well, my omni is tuneable, so, if I can lower it a little, I may be able to get by without another antenna. But, I don't need that at the moment. Sucks that two item's I can't get shipped unfortunately are cement and any pipes that are usually over five feet long. Anything else I can order. Considering I don't own a truck, I mean.

Link to comment
Share on other sites

Okay. Well, I may need to reconsider that length or use something else. I think while It's up, it will last years being straight. But, each time I lower and raise it, It's going to get bent little by little lol. Perhaps if I attach my winch to the top segment, It'll keep it all straight while lowering and raising. I won't be lowering and raising often, only for hurricanes or repairs. But, It's kind of being raised and lowered often at the moment because I'm still working on stuff. I didn't think it would bend that easy, though. Because the top segment is only taking about 3lbs from the antenna, and, the second segment is taking about 5lbs from the top segment and 3lbs from the antenna. The bottom segment doesn't really bend because the setup keeps that one stiff while raising and lowering it.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use and Guidelines.