Jump to content

Search the Community

Showing results for tags 'PA'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


  • General Mobile Radio Service (GMRS)
    • Guest Forum
    • General Discussion
    • Technical Discussion
    • Equipment Reviews
    • FCC Rules Discussion
    • myGMRS.com
    • National and Regional GMRS Nets
  • Other Radio Services
    • Family Radio Service (FRS)
    • Multi-Use Radio Service (MURS)
    • Amateur Radio (Ham)
    • 900 MHz License-Free Radios (ISM)
  • Off-Topic
    • Miscellaneous Topics
  • TreasurecoastGMRSclub's Radio Etiuette
  • TreasurecoastGMRSclub's Radio gear
  • South Western PA GMRS's Repeaters
  • NOVA GMRS's Area Repeaters
  • ISLACOMM GMRS's Topics
  • Alaska GMRS's Welcome!
  • Southwest Virginia GMRS's Topics
  • Ozark Plateau GMRS's Questions
  • Ozark Plateau GMRS's General Discussion


  • Community Calendar
  • ISLACOMM GMRS's Events
  • Southdade GMRS Club's Events
  • Southwest Virginia GMRS's Events

Find results in...

Find results that contain...

Date Created

  • Start


Last Updated

  • Start


Filter by number of...


  • Start



Website URL




Unit Number




GMRS Callsign

Ham Callsign

Found 2 results

  1. Hello all, Does anyone know if it is possible to lower the wattage output on a radius M1225? I read in repeater-builder that an m1225 was a good exciter for a (stand alone) msf-5000 pa . The Msf-5000 has an input of >5watts give or take.... I do have the rss (windows xp) for the Motorola m1225, I'm thinking, there might be a way, to adjust output wattage, in the service feature? Also I've read in forums (years ago) that people would adjust the m1225 potentiometer, when programming out of band, for ham use.... I'm putting together a repeater in the vhf business bands. I was also thinking an inline attenuator, but that kinda defeats the purpose of increasing the duty cycle, even on low,15 watts...just more heat generated that needs to be exhausted. Please and thank you for any help you can give me in this matter. d
  2. So a few weeks ago I took my repeater offline due to transmitter issues. I run a RKR1225 (rack mount version of the GR1225) and of course this repeater is known for its issues with burned out finals in the PA. At the time the unit was putting out .1W of its 25W of power. I didn't have time to pull the unit from the rack and disassemble the shelf so for a bit, out of wanting to protect components, I just shut the repeater off. Fearing a PA failure I was in no rush to dismantle anything until I knew I could get the parts or ship it out to a shop for repairs. When the time came earlier this week, I contacted a shop who said I needed to confirm the PA had not already been replaced as they couldn't repair an already repaired amp. So I pulled the shelf from the rack and began to dismantle it so I could remove the radio body, however when I removed the TX jumper from the radio, I found that the coax had failed, separating from the connector. From just looking at it you couldn't tell, but everything, the center pin and the shield, had come apart and simply slid out of the end of the connector and rest in my hand!! Concerned the PA may have been damaged because of this, I found a crap jumper I had set aside when I was given the double shielded jumper. I ran it through the meter and into a dummy load and behold, TX power returned to 25W! A little more testing, including the duplexer showed everything was working fine. I figured I would test the coax separately with a test meter for coax and sure enough it showed high resistance and feedback in the little 1' jumper. In the end I purchased 2 jumpers, a bit longer than the one I was replacing as I believe the older one could have been pulled on during install. I replaced both the RX and TX jumpers with LMR240 coax and the result is that not only did the TX power come back, but the range extended a little bit as well. This is just a reminder that even the simplest of things such as a jumper can mimic larger more costly problems. I believed it was going to be nearly $150 to repair the repeater and I even considered just replacing the unit with one that could run 50W on a 100% duty cycle. All I really needed was a $15 jumper to replace the one that failed. For those of us diagnosing issues for repairs we need to keep in mind that its not always the common problem causing the issue, and we need to make sure we always check the simple stuff we often overlook such as jumpers which are not a common failure point.
  • Create New...

Important Information

By using this site, you agree to our Terms of Use and Guidelines.