coryb27

What does “duty cycle” mean?
 
I bring up duty cycle every time I hear somebody talking about making a repeater out of cheap Chinese mobiles and worse any type of handhelds. Duty cycle is the maximum time an amplifier may transmit within a five minute interval, expressed as a percentage, to avoid overheating. Suppose a mobile amplifier is rated at 30% duty cycle. This means that it may transmit for no longer than 1.5 minutes and must remain off for not less than 3.5 minutes. Some people forget that a repeater is transmitting for 2 or more people, duty cycle will be reached quickly if you get into conversation. More people in the conversation just amplifies the issue.
 
Once a radio reaches it's thermal design limits it will no longer be able to adequately cool the output transistors. Even if a radio is not hot to the touch the transistors are, in part because of the inefficient transfer of heat to the units housing or internal heat sink. The longer you exceed the duty cycle the more heat builds on the transistors, surrounding electronics and heat sink effecting it's ability to remain on frequency without spurious emissions. Exceed duty cycle long enough and you will need a new transmitter or radio.
 
I have tested a few Baofang and TYT radios on my service monitor without great results. All of the radios started deviating outside of the allotted channel bandwidth after simulated conversation at 50% duty cycle, the longer I allowed this the worse if got. Testing was done using an Aeroflex 2975 IFR recently back from the calibration lab. 
 
GMRS is a tiny sliver of spectrum surrounded by the commercial land mobile part 90 service. It is important that any repeaters that are built or re-purposed are held to the highest standards and operated as to not cause any interference inside or outside of our allocated spectrum. I wont get into the part 90/95 debate but i do stand firm that non certified import equipment has no place on GMRS. 

Why does every new license holder want to setup a repeater? I would like to shed a little light on some of the important things to consider if you recently got your GMRS license and now want your own repeater.
 
First thing to consider, are there any open well placed repeaters in your area that you are able to use? I can assure you most repeater owners want people to use there repeater. Owning several repeaters I can assure you all are welcome and encouraged to use my machines.
 
Do you have access to a location to host your repeater? If your answer is your garage roof you should reconsider. Your garage roof will give you about the same coverage as simplex. Unless you’re on top of a mountain and all your users are at the bottom you will never be happy with this setup.
 
GMRS is not as popular as one would like to think, unless your repeater covers 20 miles or more you may find you only have 1 or 2 users in the area. Unless you already have a group of friends together you may want to consider this before spending money on a decent well positioned site to install your repeater.
 
So you found a nice high site and the price is right, all you need to do is get the repeater installed, sounds simple right? Some thigs to consider first and foremost are the costs because they can add up quickly. Are you on a commercial tower that requires a license and bonded climber? If so this could be by far your largest expense depending on your area. I have spent $600 to $1200 on a climber; I have had quotes as high as $2500 depending on the amount of work and heights involved.  Keep in mind commercial sites require certified mounts, hard line cable, cable clamps, engineered grounding solutions and commercial grade antennas. No tower owner is going to let you install a comet antenna and 200’ of braided shield coax.
 
This brings me to my next point, the antenna. Because of the costs involved with climbers you will want to expend your budget on the antenna. Remember a $2000 repeater on a $200 antenna is going to work about as good as a $200 repeater.  Whereas a $200 repeater on a $2000 antenna is going to work like a $2000 repeater. On my first repeater I was gifted use of a 150’ tower, I installed a DB-420 on the top and 160’ of 7/8 hardline. Total cost of equipment for the antenna install was $2500, with the climbers labor coming in at an additional $800. This left me with enough to purchase an old Motorola R100 repeater running at 25W. To my surprise it had 30 miles of coverage, all due to the cash spent on the antenna and waiting for a decent spot.
 
Things happen, more so if you have an antenna 200’ in the air with a conductive cable connected to sensitive electronics. Antenna issues, feedline issues, repeater issues all cost money and I promise at some point you will have issues that need repair and require your money!
 
It is my opinion that the GMRS community does not need another 2 to 5 miles repeater as it just becomes background noise. What use is a public listed repeater if somebody in a mobile can’t use it 5 miles away while moving or the portable coverage is only a mile? If after reading this you are still going to build a repeater for your garage more power to you, just don’t expect 20 people to show up if it only reaches a mile.
 
As the owner of several GMRS and Commercial repeaters I can attest to the amount of money and effort go into my repeaters. I have only touched on the basics, if you add in any kind of testing services, duplexer tuning, addition of a combiner channel to an existing tower system, RF engineering, rent and insurance your costs can sky rocket. The best advice I can give any new licensee is to try and use the available systems in the area. Take the time to learn a little about what you’re doing and to assess the usability of the service before investing in a repeater for the sole reason of saying you own one.

Why does every new license holder want to setup a repeater? I would like to shed a little light on some of the important things to consider if you recently got your GMRS license and now want your own repeater.
 
First thing to consider, are there any open well placed repeaters in your area that you are able to use? I can assure you most repeater owners want people to use there repeater. Owning several repeaters I can assure you all are welcome and encouraged to use my machines.
 
Do you have access to a location to host your repeater? If your answer is your garage roof you should reconsider. Your garage roof will give you about the same coverage as simplex. Unless you’re on top of a mountain and all your users are at the bottom you will never be happy with this setup.
 
GMRS is not as popular as one would like to think, unless your repeater covers 20 miles or more you may find you only have 1 or 2 users in the area. Unless you already have a group of friends together you may want to consider this before spending money on a decent well positioned site to install your repeater.
 
So you found a nice high site and the price is right, all you need to do is get the repeater installed, sounds simple right? Some thigs to consider first and foremost are the costs because they can add up quickly. Are you on a commercial tower that requires a license and bonded climber? If so this could be by far your largest expense depending on your area. I have spent $600 to $1200 on a climber; I have had quotes as high as $2500 depending on the amount of work and heights involved.  Keep in mind commercial sites require certified mounts, hard line cable, cable clamps, engineered grounding solutions and commercial grade antennas. No tower owner is going to let you install a comet antenna and 200’ of braided shield coax.
 
This brings me to my next point, the antenna. Because of the costs involved with climbers you will want to expend your budget on the antenna. Remember a $2000 repeater on a $200 antenna is going to work about as good as a $200 repeater.  Whereas a $200 repeater on a $2000 antenna is going to work like a $2000 repeater. On my first repeater I was gifted use of a 150’ tower, I installed a DB-420 on the top and 160’ of 7/8 hardline. Total cost of equipment for the antenna install was $2500, with the climbers labor coming in at an additional $800. This left me with enough to purchase an old Motorola R100 repeater running at 25W. To my surprise it had 30 miles of coverage, all due to the cash spent on the antenna and waiting for a decent spot.
 
Things happen, more so if you have an antenna 200’ in the air with a conductive cable connected to sensitive electronics. Antenna issues, feedline issues, repeater issues all cost money and I promise at some point you will have issues that need repair and require your money!
 
It is my opinion that the GMRS community does not need another 2 to 5 miles repeater as it just becomes background noise. What use is a public listed repeater if somebody in a mobile can’t use it 5 miles away while moving or the portable coverage is only a mile? If after reading this you are still going to build a repeater for your garage more power to you, just don’t expect 20 people to show up if it only reaches a mile.
 
As the owner of several GMRS and Commercial repeaters I can attest to the amount of money and effort go into my repeaters. I have only touched on the basics, if you add in any kind of testing services, duplexer tuning, addition of a combiner channel to an existing tower system, RF engineering, rent and insurance your costs can sky rocket. The best advice I can give any new licensee is to try and use the available systems in the area. Take the time to learn a little about what you’re doing and to assess the usability of the service before investing in a repeater for the sole reason of saying you own one.

Why does every new license holder want to setup a repeater? I would like to shed a little light on some of the important things to consider if you recently got your GMRS license and now want your own repeater.
 
First thing to consider, are there any open well placed repeaters in your area that you are able to use? I can assure you most repeater owners want people to use there repeater. Owning several repeaters I can assure you all are welcome and encouraged to use my machines.
 
Do you have access to a location to host your repeater? If your answer is your garage roof you should reconsider. Your garage roof will give you about the same coverage as simplex. Unless you’re on top of a mountain and all your users are at the bottom you will never be happy with this setup.
 
GMRS is not as popular as one would like to think, unless your repeater covers 20 miles or more you may find you only have 1 or 2 users in the area. Unless you already have a group of friends together you may want to consider this before spending money on a decent well positioned site to install your repeater.
 
So you found a nice high site and the price is right, all you need to do is get the repeater installed, sounds simple right? Some thigs to consider first and foremost are the costs because they can add up quickly. Are you on a commercial tower that requires a license and bonded climber? If so this could be by far your largest expense depending on your area. I have spent $600 to $1200 on a climber; I have had quotes as high as $2500 depending on the amount of work and heights involved.  Keep in mind commercial sites require certified mounts, hard line cable, cable clamps, engineered grounding solutions and commercial grade antennas. No tower owner is going to let you install a comet antenna and 200’ of braided shield coax.
 
This brings me to my next point, the antenna. Because of the costs involved with climbers you will want to expend your budget on the antenna. Remember a $2000 repeater on a $200 antenna is going to work about as good as a $200 repeater.  Whereas a $200 repeater on a $2000 antenna is going to work like a $2000 repeater. On my first repeater I was gifted use of a 150’ tower, I installed a DB-420 on the top and 160’ of 7/8 hardline. Total cost of equipment for the antenna install was $2500, with the climbers labor coming in at an additional $800. This left me with enough to purchase an old Motorola R100 repeater running at 25W. To my surprise it had 30 miles of coverage, all due to the cash spent on the antenna and waiting for a decent spot.
 
Things happen, more so if you have an antenna 200’ in the air with a conductive cable connected to sensitive electronics. Antenna issues, feedline issues, repeater issues all cost money and I promise at some point you will have issues that need repair and require your money!
 
It is my opinion that the GMRS community does not need another 2 to 5 miles repeater as it just becomes background noise. What use is a public listed repeater if somebody in a mobile can’t use it 5 miles away while moving or the portable coverage is only a mile? If after reading this you are still going to build a repeater for your garage more power to you, just don’t expect 20 people to show up if it only reaches a mile.
 
As the owner of several GMRS and Commercial repeaters I can attest to the amount of money and effort go into my repeaters. I have only touched on the basics, if you add in any kind of testing services, duplexer tuning, addition of a combiner channel to an existing tower system, RF engineering, rent and insurance your costs can sky rocket. The best advice I can give any new licensee is to try and use the available systems in the area. Take the time to learn a little about what you’re doing and to assess the usability of the service before investing in a repeater for the sole reason of saying you own one.

Why does every new license holder want to setup a repeater? I would like to shed a little light on some of the important things to consider if you recently got your GMRS license and now want your own repeater.
 
First thing to consider, are there any open well placed repeaters in your area that you are able to use? I can assure you most repeater owners want people to use there repeater. Owning several repeaters I can assure you all are welcome and encouraged to use my machines.
 
Do you have access to a location to host your repeater? If your answer is your garage roof you should reconsider. Your garage roof will give you about the same coverage as simplex. Unless you’re on top of a mountain and all your users are at the bottom you will never be happy with this setup.
 
GMRS is not as popular as one would like to think, unless your repeater covers 20 miles or more you may find you only have 1 or 2 users in the area. Unless you already have a group of friends together you may want to consider this before spending money on a decent well positioned site to install your repeater.
 
So you found a nice high site and the price is right, all you need to do is get the repeater installed, sounds simple right? Some thigs to consider first and foremost are the costs because they can add up quickly. Are you on a commercial tower that requires a license and bonded climber? If so this could be by far your largest expense depending on your area. I have spent $600 to $1200 on a climber; I have had quotes as high as $2500 depending on the amount of work and heights involved.  Keep in mind commercial sites require certified mounts, hard line cable, cable clamps, engineered grounding solutions and commercial grade antennas. No tower owner is going to let you install a comet antenna and 200’ of braided shield coax.
 
This brings me to my next point, the antenna. Because of the costs involved with climbers you will want to expend your budget on the antenna. Remember a $2000 repeater on a $200 antenna is going to work about as good as a $200 repeater.  Whereas a $200 repeater on a $2000 antenna is going to work like a $2000 repeater. On my first repeater I was gifted use of a 150’ tower, I installed a DB-420 on the top and 160’ of 7/8 hardline. Total cost of equipment for the antenna install was $2500, with the climbers labor coming in at an additional $800. This left me with enough to purchase an old Motorola R100 repeater running at 25W. To my surprise it had 30 miles of coverage, all due to the cash spent on the antenna and waiting for a decent spot.
 
Things happen, more so if you have an antenna 200’ in the air with a conductive cable connected to sensitive electronics. Antenna issues, feedline issues, repeater issues all cost money and I promise at some point you will have issues that need repair and require your money!
 
It is my opinion that the GMRS community does not need another 2 to 5 miles repeater as it just becomes background noise. What use is a public listed repeater if somebody in a mobile can’t use it 5 miles away while moving or the portable coverage is only a mile? If after reading this you are still going to build a repeater for your garage more power to you, just don’t expect 20 people to show up if it only reaches a mile.
 
As the owner of several GMRS and Commercial repeaters I can attest to the amount of money and effort go into my repeaters. I have only touched on the basics, if you add in any kind of testing services, duplexer tuning, addition of a combiner channel to an existing tower system, RF engineering, rent and insurance your costs can sky rocket. The best advice I can give any new licensee is to try and use the available systems in the area. Take the time to learn a little about what you’re doing and to assess the usability of the service before investing in a repeater for the sole reason of saying you own one.

Why does every new license holder want to setup a repeater? I would like to shed a little light on some of the important things to consider if you recently got your GMRS license and now want your own repeater.
 
First thing to consider, are there any open well placed repeaters in your area that you are able to use? I can assure you most repeater owners want people to use there repeater. Owning several repeaters I can assure you all are welcome and encouraged to use my machines.
 
Do you have access to a location to host your repeater? If your answer is your garage roof you should reconsider. Your garage roof will give you about the same coverage as simplex. Unless you’re on top of a mountain and all your users are at the bottom you will never be happy with this setup.
 
GMRS is not as popular as one would like to think, unless your repeater covers 20 miles or more you may find you only have 1 or 2 users in the area. Unless you already have a group of friends together you may want to consider this before spending money on a decent well positioned site to install your repeater.
 
So you found a nice high site and the price is right, all you need to do is get the repeater installed, sounds simple right? Some thigs to consider first and foremost are the costs because they can add up quickly. Are you on a commercial tower that requires a license and bonded climber? If so this could be by far your largest expense depending on your area. I have spent $600 to $1200 on a climber; I have had quotes as high as $2500 depending on the amount of work and heights involved.  Keep in mind commercial sites require certified mounts, hard line cable, cable clamps, engineered grounding solutions and commercial grade antennas. No tower owner is going to let you install a comet antenna and 200’ of braided shield coax.
 
This brings me to my next point, the antenna. Because of the costs involved with climbers you will want to expend your budget on the antenna. Remember a $2000 repeater on a $200 antenna is going to work about as good as a $200 repeater.  Whereas a $200 repeater on a $2000 antenna is going to work like a $2000 repeater. On my first repeater I was gifted use of a 150’ tower, I installed a DB-420 on the top and 160’ of 7/8 hardline. Total cost of equipment for the antenna install was $2500, with the climbers labor coming in at an additional $800. This left me with enough to purchase an old Motorola R100 repeater running at 25W. To my surprise it had 30 miles of coverage, all due to the cash spent on the antenna and waiting for a decent spot.
 
Things happen, more so if you have an antenna 200’ in the air with a conductive cable connected to sensitive electronics. Antenna issues, feedline issues, repeater issues all cost money and I promise at some point you will have issues that need repair and require your money!
 
It is my opinion that the GMRS community does not need another 2 to 5 miles repeater as it just becomes background noise. What use is a public listed repeater if somebody in a mobile can’t use it 5 miles away while moving or the portable coverage is only a mile? If after reading this you are still going to build a repeater for your garage more power to you, just don’t expect 20 people to show up if it only reaches a mile.
 
As the owner of several GMRS and Commercial repeaters I can attest to the amount of money and effort go into my repeaters. I have only touched on the basics, if you add in any kind of testing services, duplexer tuning, addition of a combiner channel to an existing tower system, RF engineering, rent and insurance your costs can sky rocket. The best advice I can give any new licensee is to try and use the available systems in the area. Take the time to learn a little about what you’re doing and to assess the usability of the service before investing in a repeater for the sole reason of saying you own one.

Why does every new license holder want to setup a repeater? I would like to shed a little light on some of the important things to consider if you recently got your GMRS license and now want your own repeater.
 
First thing to consider, are there any open well placed repeaters in your area that you are able to use? I can assure you most repeater owners want people to use there repeater. Owning several repeaters I can assure you all are welcome and encouraged to use my machines.
 
Do you have access to a location to host your repeater? If your answer is your garage roof you should reconsider. Your garage roof will give you about the same coverage as simplex. Unless you’re on top of a mountain and all your users are at the bottom you will never be happy with this setup.
 
GMRS is not as popular as one would like to think, unless your repeater covers 20 miles or more you may find you only have 1 or 2 users in the area. Unless you already have a group of friends together you may want to consider this before spending money on a decent well positioned site to install your repeater.
 
So you found a nice high site and the price is right, all you need to do is get the repeater installed, sounds simple right? Some thigs to consider first and foremost are the costs because they can add up quickly. Are you on a commercial tower that requires a license and bonded climber? If so this could be by far your largest expense depending on your area. I have spent $600 to $1200 on a climber; I have had quotes as high as $2500 depending on the amount of work and heights involved.  Keep in mind commercial sites require certified mounts, hard line cable, cable clamps, engineered grounding solutions and commercial grade antennas. No tower owner is going to let you install a comet antenna and 200’ of braided shield coax.
 
This brings me to my next point, the antenna. Because of the costs involved with climbers you will want to expend your budget on the antenna. Remember a $2000 repeater on a $200 antenna is going to work about as good as a $200 repeater.  Whereas a $200 repeater on a $2000 antenna is going to work like a $2000 repeater. On my first repeater I was gifted use of a 150’ tower, I installed a DB-420 on the top and 160’ of 7/8 hardline. Total cost of equipment for the antenna install was $2500, with the climbers labor coming in at an additional $800. This left me with enough to purchase an old Motorola R100 repeater running at 25W. To my surprise it had 30 miles of coverage, all due to the cash spent on the antenna and waiting for a decent spot.
 
Things happen, more so if you have an antenna 200’ in the air with a conductive cable connected to sensitive electronics. Antenna issues, feedline issues, repeater issues all cost money and I promise at some point you will have issues that need repair and require your money!
 
It is my opinion that the GMRS community does not need another 2 to 5 miles repeater as it just becomes background noise. What use is a public listed repeater if somebody in a mobile can’t use it 5 miles away while moving or the portable coverage is only a mile? If after reading this you are still going to build a repeater for your garage more power to you, just don’t expect 20 people to show up if it only reaches a mile.
 
As the owner of several GMRS and Commercial repeaters I can attest to the amount of money and effort go into my repeaters. I have only touched on the basics, if you add in any kind of testing services, duplexer tuning, addition of a combiner channel to an existing tower system, RF engineering, rent and insurance your costs can sky rocket. The best advice I can give any new licensee is to try and use the available systems in the area. Take the time to learn a little about what you’re doing and to assess the usability of the service before investing in a repeater for the sole reason of saying you own one.

Why does every new license holder want to setup a repeater? I would like to shed a little light on some of the important things to consider if you recently got your GMRS license and now want your own repeater.
 
First thing to consider, are there any open well placed repeaters in your area that you are able to use? I can assure you most repeater owners want people to use there repeater. Owning several repeaters I can assure you all are welcome and encouraged to use my machines.
 
Do you have access to a location to host your repeater? If your answer is your garage roof you should reconsider. Your garage roof will give you about the same coverage as simplex. Unless you’re on top of a mountain and all your users are at the bottom you will never be happy with this setup.
 
GMRS is not as popular as one would like to think, unless your repeater covers 20 miles or more you may find you only have 1 or 2 users in the area. Unless you already have a group of friends together you may want to consider this before spending money on a decent well positioned site to install your repeater.
 
So you found a nice high site and the price is right, all you need to do is get the repeater installed, sounds simple right? Some thigs to consider first and foremost are the costs because they can add up quickly. Are you on a commercial tower that requires a license and bonded climber? If so this could be by far your largest expense depending on your area. I have spent $600 to $1200 on a climber; I have had quotes as high as $2500 depending on the amount of work and heights involved.  Keep in mind commercial sites require certified mounts, hard line cable, cable clamps, engineered grounding solutions and commercial grade antennas. No tower owner is going to let you install a comet antenna and 200’ of braided shield coax.
 
This brings me to my next point, the antenna. Because of the costs involved with climbers you will want to expend your budget on the antenna. Remember a $2000 repeater on a $200 antenna is going to work about as good as a $200 repeater.  Whereas a $200 repeater on a $2000 antenna is going to work like a $2000 repeater. On my first repeater I was gifted use of a 150’ tower, I installed a DB-420 on the top and 160’ of 7/8 hardline. Total cost of equipment for the antenna install was $2500, with the climbers labor coming in at an additional $800. This left me with enough to purchase an old Motorola R100 repeater running at 25W. To my surprise it had 30 miles of coverage, all due to the cash spent on the antenna and waiting for a decent spot.
 
Things happen, more so if you have an antenna 200’ in the air with a conductive cable connected to sensitive electronics. Antenna issues, feedline issues, repeater issues all cost money and I promise at some point you will have issues that need repair and require your money!
 
It is my opinion that the GMRS community does not need another 2 to 5 miles repeater as it just becomes background noise. What use is a public listed repeater if somebody in a mobile can’t use it 5 miles away while moving or the portable coverage is only a mile? If after reading this you are still going to build a repeater for your garage more power to you, just don’t expect 20 people to show up if it only reaches a mile.
 
As the owner of several GMRS and Commercial repeaters I can attest to the amount of money and effort go into my repeaters. I have only touched on the basics, if you add in any kind of testing services, duplexer tuning, addition of a combiner channel to an existing tower system, RF engineering, rent and insurance your costs can sky rocket. The best advice I can give any new licensee is to try and use the available systems in the area. Take the time to learn a little about what you’re doing and to assess the usability of the service before investing in a repeater for the sole reason of saying you own one.

Why does every new license holder want to setup a repeater? I would like to shed a little light on some of the important things to consider if you recently got your GMRS license and now want your own repeater.
 
First thing to consider, are there any open well placed repeaters in your area that you are able to use? I can assure you most repeater owners want people to use there repeater. Owning several repeaters I can assure you all are welcome and encouraged to use my machines.
 
Do you have access to a location to host your repeater? If your answer is your garage roof you should reconsider. Your garage roof will give you about the same coverage as simplex. Unless you’re on top of a mountain and all your users are at the bottom you will never be happy with this setup.
 
GMRS is not as popular as one would like to think, unless your repeater covers 20 miles or more you may find you only have 1 or 2 users in the area. Unless you already have a group of friends together you may want to consider this before spending money on a decent well positioned site to install your repeater.
 
So you found a nice high site and the price is right, all you need to do is get the repeater installed, sounds simple right? Some thigs to consider first and foremost are the costs because they can add up quickly. Are you on a commercial tower that requires a license and bonded climber? If so this could be by far your largest expense depending on your area. I have spent $600 to $1200 on a climber; I have had quotes as high as $2500 depending on the amount of work and heights involved.  Keep in mind commercial sites require certified mounts, hard line cable, cable clamps, engineered grounding solutions and commercial grade antennas. No tower owner is going to let you install a comet antenna and 200’ of braided shield coax.
 
This brings me to my next point, the antenna. Because of the costs involved with climbers you will want to expend your budget on the antenna. Remember a $2000 repeater on a $200 antenna is going to work about as good as a $200 repeater.  Whereas a $200 repeater on a $2000 antenna is going to work like a $2000 repeater. On my first repeater I was gifted use of a 150’ tower, I installed a DB-420 on the top and 160’ of 7/8 hardline. Total cost of equipment for the antenna install was $2500, with the climbers labor coming in at an additional $800. This left me with enough to purchase an old Motorola R100 repeater running at 25W. To my surprise it had 30 miles of coverage, all due to the cash spent on the antenna and waiting for a decent spot.
 
Things happen, more so if you have an antenna 200’ in the air with a conductive cable connected to sensitive electronics. Antenna issues, feedline issues, repeater issues all cost money and I promise at some point you will have issues that need repair and require your money!
 
It is my opinion that the GMRS community does not need another 2 to 5 miles repeater as it just becomes background noise. What use is a public listed repeater if somebody in a mobile can’t use it 5 miles away while moving or the portable coverage is only a mile? If after reading this you are still going to build a repeater for your garage more power to you, just don’t expect 20 people to show up if it only reaches a mile.
 
As the owner of several GMRS and Commercial repeaters I can attest to the amount of money and effort go into my repeaters. I have only touched on the basics, if you add in any kind of testing services, duplexer tuning, addition of a combiner channel to an existing tower system, RF engineering, rent and insurance your costs can sky rocket. The best advice I can give any new licensee is to try and use the available systems in the area. Take the time to learn a little about what you’re doing and to assess the usability of the service before investing in a repeater for the sole reason of saying you own one.

Why does every new license holder want to setup a repeater? I would like to shed a little light on some of the important things to consider if you recently got your GMRS license and now want your own repeater.
 
First thing to consider, are there any open well placed repeaters in your area that you are able to use? I can assure you most repeater owners want people to use there repeater. Owning several repeaters I can assure you all are welcome and encouraged to use my machines.
 
Do you have access to a location to host your repeater? If your answer is your garage roof you should reconsider. Your garage roof will give you about the same coverage as simplex. Unless you’re on top of a mountain and all your users are at the bottom you will never be happy with this setup.
 
GMRS is not as popular as one would like to think, unless your repeater covers 20 miles or more you may find you only have 1 or 2 users in the area. Unless you already have a group of friends together you may want to consider this before spending money on a decent well positioned site to install your repeater.
 
So you found a nice high site and the price is right, all you need to do is get the repeater installed, sounds simple right? Some thigs to consider first and foremost are the costs because they can add up quickly. Are you on a commercial tower that requires a license and bonded climber? If so this could be by far your largest expense depending on your area. I have spent $600 to $1200 on a climber; I have had quotes as high as $2500 depending on the amount of work and heights involved.  Keep in mind commercial sites require certified mounts, hard line cable, cable clamps, engineered grounding solutions and commercial grade antennas. No tower owner is going to let you install a comet antenna and 200’ of braided shield coax.
 
This brings me to my next point, the antenna. Because of the costs involved with climbers you will want to expend your budget on the antenna. Remember a $2000 repeater on a $200 antenna is going to work about as good as a $200 repeater.  Whereas a $200 repeater on a $2000 antenna is going to work like a $2000 repeater. On my first repeater I was gifted use of a 150’ tower, I installed a DB-420 on the top and 160’ of 7/8 hardline. Total cost of equipment for the antenna install was $2500, with the climbers labor coming in at an additional $800. This left me with enough to purchase an old Motorola R100 repeater running at 25W. To my surprise it had 30 miles of coverage, all due to the cash spent on the antenna and waiting for a decent spot.
 
Things happen, more so if you have an antenna 200’ in the air with a conductive cable connected to sensitive electronics. Antenna issues, feedline issues, repeater issues all cost money and I promise at some point you will have issues that need repair and require your money!
 
It is my opinion that the GMRS community does not need another 2 to 5 miles repeater as it just becomes background noise. What use is a public listed repeater if somebody in a mobile can’t use it 5 miles away while moving or the portable coverage is only a mile? If after reading this you are still going to build a repeater for your garage more power to you, just don’t expect 20 people to show up if it only reaches a mile.
 
As the owner of several GMRS and Commercial repeaters I can attest to the amount of money and effort go into my repeaters. I have only touched on the basics, if you add in any kind of testing services, duplexer tuning, addition of a combiner channel to an existing tower system, RF engineering, rent and insurance your costs can sky rocket. The best advice I can give any new licensee is to try and use the available systems in the area. Take the time to learn a little about what you’re doing and to assess the usability of the service before investing in a repeater for the sole reason of saying you own one.

Why does every new license holder want to setup a repeater? I would like to shed a little light on some of the important things to consider if you recently got your GMRS license and now want your own repeater.
 
First thing to consider, are there any open well placed repeaters in your area that you are able to use? I can assure you most repeater owners want people to use there repeater. Owning several repeaters I can assure you all are welcome and encouraged to use my machines.
 
Do you have access to a location to host your repeater? If your answer is your garage roof you should reconsider. Your garage roof will give you about the same coverage as simplex. Unless you’re on top of a mountain and all your users are at the bottom you will never be happy with this setup.
 
GMRS is not as popular as one would like to think, unless your repeater covers 20 miles or more you may find you only have 1 or 2 users in the area. Unless you already have a group of friends together you may want to consider this before spending money on a decent well positioned site to install your repeater.
 
So you found a nice high site and the price is right, all you need to do is get the repeater installed, sounds simple right? Some thigs to consider first and foremost are the costs because they can add up quickly. Are you on a commercial tower that requires a license and bonded climber? If so this could be by far your largest expense depending on your area. I have spent $600 to $1200 on a climber; I have had quotes as high as $2500 depending on the amount of work and heights involved.  Keep in mind commercial sites require certified mounts, hard line cable, cable clamps, engineered grounding solutions and commercial grade antennas. No tower owner is going to let you install a comet antenna and 200’ of braided shield coax.
 
This brings me to my next point, the antenna. Because of the costs involved with climbers you will want to expend your budget on the antenna. Remember a $2000 repeater on a $200 antenna is going to work about as good as a $200 repeater.  Whereas a $200 repeater on a $2000 antenna is going to work like a $2000 repeater. On my first repeater I was gifted use of a 150’ tower, I installed a DB-420 on the top and 160’ of 7/8 hardline. Total cost of equipment for the antenna install was $2500, with the climbers labor coming in at an additional $800. This left me with enough to purchase an old Motorola R100 repeater running at 25W. To my surprise it had 30 miles of coverage, all due to the cash spent on the antenna and waiting for a decent spot.
 
Things happen, more so if you have an antenna 200’ in the air with a conductive cable connected to sensitive electronics. Antenna issues, feedline issues, repeater issues all cost money and I promise at some point you will have issues that need repair and require your money!
 
It is my opinion that the GMRS community does not need another 2 to 5 miles repeater as it just becomes background noise. What use is a public listed repeater if somebody in a mobile can’t use it 5 miles away while moving or the portable coverage is only a mile? If after reading this you are still going to build a repeater for your garage more power to you, just don’t expect 20 people to show up if it only reaches a mile.
 
As the owner of several GMRS and Commercial repeaters I can attest to the amount of money and effort go into my repeaters. I have only touched on the basics, if you add in any kind of testing services, duplexer tuning, addition of a combiner channel to an existing tower system, RF engineering, rent and insurance your costs can sky rocket. The best advice I can give any new licensee is to try and use the available systems in the area. Take the time to learn a little about what you’re doing and to assess the usability of the service before investing in a repeater for the sole reason of saying you own one.

Why does every new license holder want to setup a repeater? I would like to shed a little light on some of the important things to consider if you recently got your GMRS license and now want your own repeater.
 
First thing to consider, are there any open well placed repeaters in your area that you are able to use? I can assure you most repeater owners want people to use there repeater. Owning several repeaters I can assure you all are welcome and encouraged to use my machines.
 
Do you have access to a location to host your repeater? If your answer is your garage roof you should reconsider. Your garage roof will give you about the same coverage as simplex. Unless you’re on top of a mountain and all your users are at the bottom you will never be happy with this setup.
 
GMRS is not as popular as one would like to think, unless your repeater covers 20 miles or more you may find you only have 1 or 2 users in the area. Unless you already have a group of friends together you may want to consider this before spending money on a decent well positioned site to install your repeater.
 
So you found a nice high site and the price is right, all you need to do is get the repeater installed, sounds simple right? Some thigs to consider first and foremost are the costs because they can add up quickly. Are you on a commercial tower that requires a license and bonded climber? If so this could be by far your largest expense depending on your area. I have spent $600 to $1200 on a climber; I have had quotes as high as $2500 depending on the amount of work and heights involved.  Keep in mind commercial sites require certified mounts, hard line cable, cable clamps, engineered grounding solutions and commercial grade antennas. No tower owner is going to let you install a comet antenna and 200’ of braided shield coax.
 
This brings me to my next point, the antenna. Because of the costs involved with climbers you will want to expend your budget on the antenna. Remember a $2000 repeater on a $200 antenna is going to work about as good as a $200 repeater.  Whereas a $200 repeater on a $2000 antenna is going to work like a $2000 repeater. On my first repeater I was gifted use of a 150’ tower, I installed a DB-420 on the top and 160’ of 7/8 hardline. Total cost of equipment for the antenna install was $2500, with the climbers labor coming in at an additional $800. This left me with enough to purchase an old Motorola R100 repeater running at 25W. To my surprise it had 30 miles of coverage, all due to the cash spent on the antenna and waiting for a decent spot.
 
Things happen, more so if you have an antenna 200’ in the air with a conductive cable connected to sensitive electronics. Antenna issues, feedline issues, repeater issues all cost money and I promise at some point you will have issues that need repair and require your money!
 
It is my opinion that the GMRS community does not need another 2 to 5 miles repeater as it just becomes background noise. What use is a public listed repeater if somebody in a mobile can’t use it 5 miles away while moving or the portable coverage is only a mile? If after reading this you are still going to build a repeater for your garage more power to you, just don’t expect 20 people to show up if it only reaches a mile.
 
As the owner of several GMRS and Commercial repeaters I can attest to the amount of money and effort go into my repeaters. I have only touched on the basics, if you add in any kind of testing services, duplexer tuning, addition of a combiner channel to an existing tower system, RF engineering, rent and insurance your costs can sky rocket. The best advice I can give any new licensee is to try and use the available systems in the area. Take the time to learn a little about what you’re doing and to assess the usability of the service before investing in a repeater for the sole reason of saying you own one.

Why does every new license holder want to setup a repeater? I would like to shed a little light on some of the important things to consider if you recently got your GMRS license and now want your own repeater.
 
First thing to consider, are there any open well placed repeaters in your area that you are able to use? I can assure you most repeater owners want people to use there repeater. Owning several repeaters I can assure you all are welcome and encouraged to use my machines.
 
Do you have access to a location to host your repeater? If your answer is your garage roof you should reconsider. Your garage roof will give you about the same coverage as simplex. Unless you’re on top of a mountain and all your users are at the bottom you will never be happy with this setup.
 
GMRS is not as popular as one would like to think, unless your repeater covers 20 miles or more you may find you only have 1 or 2 users in the area. Unless you already have a group of friends together you may want to consider this before spending money on a decent well positioned site to install your repeater.
 
So you found a nice high site and the price is right, all you need to do is get the repeater installed, sounds simple right? Some thigs to consider first and foremost are the costs because they can add up quickly. Are you on a commercial tower that requires a license and bonded climber? If so this could be by far your largest expense depending on your area. I have spent $600 to $1200 on a climber; I have had quotes as high as $2500 depending on the amount of work and heights involved.  Keep in mind commercial sites require certified mounts, hard line cable, cable clamps, engineered grounding solutions and commercial grade antennas. No tower owner is going to let you install a comet antenna and 200’ of braided shield coax.
 
This brings me to my next point, the antenna. Because of the costs involved with climbers you will want to expend your budget on the antenna. Remember a $2000 repeater on a $200 antenna is going to work about as good as a $200 repeater.  Whereas a $200 repeater on a $2000 antenna is going to work like a $2000 repeater. On my first repeater I was gifted use of a 150’ tower, I installed a DB-420 on the top and 160’ of 7/8 hardline. Total cost of equipment for the antenna install was $2500, with the climbers labor coming in at an additional $800. This left me with enough to purchase an old Motorola R100 repeater running at 25W. To my surprise it had 30 miles of coverage, all due to the cash spent on the antenna and waiting for a decent spot.
 
Things happen, more so if you have an antenna 200’ in the air with a conductive cable connected to sensitive electronics. Antenna issues, feedline issues, repeater issues all cost money and I promise at some point you will have issues that need repair and require your money!
 
It is my opinion that the GMRS community does not need another 2 to 5 miles repeater as it just becomes background noise. What use is a public listed repeater if somebody in a mobile can’t use it 5 miles away while moving or the portable coverage is only a mile? If after reading this you are still going to build a repeater for your garage more power to you, just don’t expect 20 people to show up if it only reaches a mile.
 
As the owner of several GMRS and Commercial repeaters I can attest to the amount of money and effort go into my repeaters. I have only touched on the basics, if you add in any kind of testing services, duplexer tuning, addition of a combiner channel to an existing tower system, RF engineering, rent and insurance your costs can sky rocket. The best advice I can give any new licensee is to try and use the available systems in the area. Take the time to learn a little about what you’re doing and to assess the usability of the service before investing in a repeater for the sole reason of saying you own one.

That's not a mobile repeater in that pic, its a HAM operating HF. As far as a mobile repeater it really is a waste of time. I have done this already and it was a total disappointment.. Unless your car is at a substantial height advantage you will not have any better coverage then simplex. Again you can and will try to explain or reason away my logic without listening to what I and others have been trying to tell you. I have tried the mobile repeater, the setup was a 50W Motorola SLR 5700 with a 4 cavity BP/BR duplexer connected to a 5.5dB gain antenna on the top of my truck. After testing for about month I realized it had no practical use and only offered slightly more range than simplex, best part I ended up needing a jump after a day at the fair. Mind you this was a $2400 repeater, $800 duplexer with an antenna that was tuned using an Anritsu S331D. I promise I nor anybody on this site will try to steer you wrong, I hold a Commercial, Amateur and GMRS license, own and operate several large repeaters and have all the gear for building, testing and maintaining these kinds of systems.

Why does every new license holder want to setup a repeater? I would like to shed a little light on some of the important things to consider if you recently got your GMRS license and now want your own repeater.
 
First thing to consider, are there any open well placed repeaters in your area that you are able to use? I can assure you most repeater owners want people to use there repeater. Owning several repeaters I can assure you all are welcome and encouraged to use my machines.
 
Do you have access to a location to host your repeater? If your answer is your garage roof you should reconsider. Your garage roof will give you about the same coverage as simplex. Unless you’re on top of a mountain and all your users are at the bottom you will never be happy with this setup.
 
GMRS is not as popular as one would like to think, unless your repeater covers 20 miles or more you may find you only have 1 or 2 users in the area. Unless you already have a group of friends together you may want to consider this before spending money on a decent well positioned site to install your repeater.
 
So you found a nice high site and the price is right, all you need to do is get the repeater installed, sounds simple right? Some thigs to consider first and foremost are the costs because they can add up quickly. Are you on a commercial tower that requires a license and bonded climber? If so this could be by far your largest expense depending on your area. I have spent $600 to $1200 on a climber; I have had quotes as high as $2500 depending on the amount of work and heights involved.  Keep in mind commercial sites require certified mounts, hard line cable, cable clamps, engineered grounding solutions and commercial grade antennas. No tower owner is going to let you install a comet antenna and 200’ of braided shield coax.
 
This brings me to my next point, the antenna. Because of the costs involved with climbers you will want to expend your budget on the antenna. Remember a $2000 repeater on a $200 antenna is going to work about as good as a $200 repeater.  Whereas a $200 repeater on a $2000 antenna is going to work like a $2000 repeater. On my first repeater I was gifted use of a 150’ tower, I installed a DB-420 on the top and 160’ of 7/8 hardline. Total cost of equipment for the antenna install was $2500, with the climbers labor coming in at an additional $800. This left me with enough to purchase an old Motorola R100 repeater running at 25W. To my surprise it had 30 miles of coverage, all due to the cash spent on the antenna and waiting for a decent spot.
 
Things happen, more so if you have an antenna 200’ in the air with a conductive cable connected to sensitive electronics. Antenna issues, feedline issues, repeater issues all cost money and I promise at some point you will have issues that need repair and require your money!
 
It is my opinion that the GMRS community does not need another 2 to 5 miles repeater as it just becomes background noise. What use is a public listed repeater if somebody in a mobile can’t use it 5 miles away while moving or the portable coverage is only a mile? If after reading this you are still going to build a repeater for your garage more power to you, just don’t expect 20 people to show up if it only reaches a mile.
 
As the owner of several GMRS and Commercial repeaters I can attest to the amount of money and effort go into my repeaters. I have only touched on the basics, if you add in any kind of testing services, duplexer tuning, addition of a combiner channel to an existing tower system, RF engineering, rent and insurance your costs can sky rocket. The best advice I can give any new licensee is to try and use the available systems in the area. Take the time to learn a little about what you’re doing and to assess the usability of the service before investing in a repeater for the sole reason of saying you own one.

I live in SW Wisconsin myself (Racine) I own or co operate several machines, 725, 700, 700, 550, 575, 675. Ingleside IL, New Berlin, Madison, Baraboo, Rhinelander and Union Grove. As far as operating under authority, this would imply a GMRS licence under authority of the issuing agency, or plainly the FCC. As such operators are required to ID by Rule of the issued licence. This term is used extensively by the FCC, you can find the definition on there site. I don't set an id on my systems for the simple reason if somebody gets on a repeater and starts breaking rules and jamming it up the last persons ID I want being broadcast is mine. Unless I am forced to by rule change I will never set and ID for this reason. Last reason is simple, its annoying to users on other repeaters sharing the channel to have some ID heterodyning during a conversation.

As far as location its being done but as far as I know does not work on repeaters. https://buy.garmin.com/en-US/US/p/533999
 
If you keyed up on my system with some rapid morse code every transmission I would give you the boot, I have no tolerance for Rodger beeps, fleet sync, etc. Lots of people use MDC to send unit numbers, around here we send the last 3 numbers of our gmrs call. Some groups send assigned unit numbers etc.. If you set your radio to decode MDC its silent and just displays it on the radio.
 
PL is stripped so the users don't have to hear it. Commercial repeaters ID every 15 min. Can you imagine having to hear that for 8 hours a day. 

That's not a mobile repeater in that pic, its a HAM operating HF. As far as a mobile repeater it really is a waste of time. I have done this already and it was a total disappointment.. Unless your car is at a substantial height advantage you will not have any better coverage then simplex. Again you can and will try to explain or reason away my logic without listening to what I and others have been trying to tell you. I have tried the mobile repeater, the setup was a 50W Motorola SLR 5700 with a 4 cavity BP/BR duplexer connected to a 5.5dB gain antenna on the top of my truck. After testing for about month I realized it had no practical use and only offered slightly more range than simplex, best part I ended up needing a jump after a day at the fair. Mind you this was a $2400 repeater, $800 duplexer with an antenna that was tuned using an Anritsu S331D. I promise I nor anybody on this site will try to steer you wrong, I hold a Commercial, Amateur and GMRS license, own and operate several large repeaters and have all the gear for building, testing and maintaining these kinds of systems.

Why does every new license holder want to setup a repeater? I would like to shed a little light on some of the important things to consider if you recently got your GMRS license and now want your own repeater.
 
First thing to consider, are there any open well placed repeaters in your area that you are able to use? I can assure you most repeater owners want people to use there repeater. Owning several repeaters I can assure you all are welcome and encouraged to use my machines.
 
Do you have access to a location to host your repeater? If your answer is your garage roof you should reconsider. Your garage roof will give you about the same coverage as simplex. Unless you’re on top of a mountain and all your users are at the bottom you will never be happy with this setup.
 
GMRS is not as popular as one would like to think, unless your repeater covers 20 miles or more you may find you only have 1 or 2 users in the area. Unless you already have a group of friends together you may want to consider this before spending money on a decent well positioned site to install your repeater.
 
So you found a nice high site and the price is right, all you need to do is get the repeater installed, sounds simple right? Some thigs to consider first and foremost are the costs because they can add up quickly. Are you on a commercial tower that requires a license and bonded climber? If so this could be by far your largest expense depending on your area. I have spent $600 to $1200 on a climber; I have had quotes as high as $2500 depending on the amount of work and heights involved.  Keep in mind commercial sites require certified mounts, hard line cable, cable clamps, engineered grounding solutions and commercial grade antennas. No tower owner is going to let you install a comet antenna and 200’ of braided shield coax.
 
This brings me to my next point, the antenna. Because of the costs involved with climbers you will want to expend your budget on the antenna. Remember a $2000 repeater on a $200 antenna is going to work about as good as a $200 repeater.  Whereas a $200 repeater on a $2000 antenna is going to work like a $2000 repeater. On my first repeater I was gifted use of a 150’ tower, I installed a DB-420 on the top and 160’ of 7/8 hardline. Total cost of equipment for the antenna install was $2500, with the climbers labor coming in at an additional $800. This left me with enough to purchase an old Motorola R100 repeater running at 25W. To my surprise it had 30 miles of coverage, all due to the cash spent on the antenna and waiting for a decent spot.
 
Things happen, more so if you have an antenna 200’ in the air with a conductive cable connected to sensitive electronics. Antenna issues, feedline issues, repeater issues all cost money and I promise at some point you will have issues that need repair and require your money!
 
It is my opinion that the GMRS community does not need another 2 to 5 miles repeater as it just becomes background noise. What use is a public listed repeater if somebody in a mobile can’t use it 5 miles away while moving or the portable coverage is only a mile? If after reading this you are still going to build a repeater for your garage more power to you, just don’t expect 20 people to show up if it only reaches a mile.
 
As the owner of several GMRS and Commercial repeaters I can attest to the amount of money and effort go into my repeaters. I have only touched on the basics, if you add in any kind of testing services, duplexer tuning, addition of a combiner channel to an existing tower system, RF engineering, rent and insurance your costs can sky rocket. The best advice I can give any new licensee is to try and use the available systems in the area. Take the time to learn a little about what you’re doing and to assess the usability of the service before investing in a repeater for the sole reason of saying you own one.

No the repeater is not required to ID, however the user is required under rule. This has been discussed many times on this site.

Why does every new license holder want to setup a repeater? I would like to shed a little light on some of the important things to consider if you recently got your GMRS license and now want your own repeater.
 
First thing to consider, are there any open well placed repeaters in your area that you are able to use? I can assure you most repeater owners want people to use there repeater. Owning several repeaters I can assure you all are welcome and encouraged to use my machines.
 
Do you have access to a location to host your repeater? If your answer is your garage roof you should reconsider. Your garage roof will give you about the same coverage as simplex. Unless you’re on top of a mountain and all your users are at the bottom you will never be happy with this setup.
 
GMRS is not as popular as one would like to think, unless your repeater covers 20 miles or more you may find you only have 1 or 2 users in the area. Unless you already have a group of friends together you may want to consider this before spending money on a decent well positioned site to install your repeater.
 
So you found a nice high site and the price is right, all you need to do is get the repeater installed, sounds simple right? Some thigs to consider first and foremost are the costs because they can add up quickly. Are you on a commercial tower that requires a license and bonded climber? If so this could be by far your largest expense depending on your area. I have spent $600 to $1200 on a climber; I have had quotes as high as $2500 depending on the amount of work and heights involved.  Keep in mind commercial sites require certified mounts, hard line cable, cable clamps, engineered grounding solutions and commercial grade antennas. No tower owner is going to let you install a comet antenna and 200’ of braided shield coax.
 
This brings me to my next point, the antenna. Because of the costs involved with climbers you will want to expend your budget on the antenna. Remember a $2000 repeater on a $200 antenna is going to work about as good as a $200 repeater.  Whereas a $200 repeater on a $2000 antenna is going to work like a $2000 repeater. On my first repeater I was gifted use of a 150’ tower, I installed a DB-420 on the top and 160’ of 7/8 hardline. Total cost of equipment for the antenna install was $2500, with the climbers labor coming in at an additional $800. This left me with enough to purchase an old Motorola R100 repeater running at 25W. To my surprise it had 30 miles of coverage, all due to the cash spent on the antenna and waiting for a decent spot.
 
Things happen, more so if you have an antenna 200’ in the air with a conductive cable connected to sensitive electronics. Antenna issues, feedline issues, repeater issues all cost money and I promise at some point you will have issues that need repair and require your money!
 
It is my opinion that the GMRS community does not need another 2 to 5 miles repeater as it just becomes background noise. What use is a public listed repeater if somebody in a mobile can’t use it 5 miles away while moving or the portable coverage is only a mile? If after reading this you are still going to build a repeater for your garage more power to you, just don’t expect 20 people to show up if it only reaches a mile.
 
As the owner of several GMRS and Commercial repeaters I can attest to the amount of money and effort go into my repeaters. I have only touched on the basics, if you add in any kind of testing services, duplexer tuning, addition of a combiner channel to an existing tower system, RF engineering, rent and insurance your costs can sky rocket. The best advice I can give any new licensee is to try and use the available systems in the area. Take the time to learn a little about what you’re doing and to assess the usability of the service before investing in a repeater for the sole reason of saying you own one.

What does “duty cycle” mean?
 
I bring up duty cycle every time I hear somebody talking about making a repeater out of cheap Chinese mobiles and worse any type of handhelds. Duty cycle is the maximum time an amplifier may transmit within a five minute interval, expressed as a percentage, to avoid overheating. Suppose a mobile amplifier is rated at 30% duty cycle. This means that it may transmit for no longer than 1.5 minutes and must remain off for not less than 3.5 minutes. Some people forget that a repeater is transmitting for 2 or more people, duty cycle will be reached quickly if you get into conversation. More people in the conversation just amplifies the issue.
 
Once a radio reaches it's thermal design limits it will no longer be able to adequately cool the output transistors. Even if a radio is not hot to the touch the transistors are, in part because of the inefficient transfer of heat to the units housing or internal heat sink. The longer you exceed the duty cycle the more heat builds on the transistors, surrounding electronics and heat sink effecting it's ability to remain on frequency without spurious emissions. Exceed duty cycle long enough and you will need a new transmitter or radio.
 
I have tested a few Baofang and TYT radios on my service monitor without great results. All of the radios started deviating outside of the allotted channel bandwidth after simulated conversation at 50% duty cycle, the longer I allowed this the worse if got. Testing was done using an Aeroflex 2975 IFR recently back from the calibration lab. 
 
GMRS is a tiny sliver of spectrum surrounded by the commercial land mobile part 90 service. It is important that any repeaters that are built or re-purposed are held to the highest standards and operated as to not cause any interference inside or outside of our allocated spectrum. I wont get into the part 90/95 debate but i do stand firm that non certified import equipment has no place on GMRS. 

I hope to write some of these at some point, just waiting for the site rebuild

I am still not sure why these posts keep appearing in GMRS groups. It is and has been legal for business to use FRS channels... People dont read the rules but claim to know them all the time. I see so much disinformation on the internet regarding the part 95 rules and some of the GMRS groups on facebook are the worst. If you try to correct the admins they block you for pointing out the truth...

If you can find an owner that will work with you. If your only options and towers owned by American Tower or Crown Castle, forget it. I had quotes in the $3.75 per foot of height with a 100 foot min. Try to find a locally owned tower or building top. I have some commercial gear on a commercial tower and pay $75 for 150' plus another $30 for internet per month. My GMRS tower was gifted to me on a long term lease for almost nothing. I have full use of the 150' and secure space with power for my gear.