Jump to content
  • 0

Repeater troubleshooting


wcpotter

Question

My guess is I am having a desense issue, but I'm not 100 percent sure.

 

The repeater works fine until I am about 1 mile away from the antenna site. Once outside of this area the audio from the mobile units stops getting through to the repeater. I know we are still reaching the repeater because we receive the squelch tail after attempting to transmit. The station ID from the controller can be heard loud and clear within a 3 town radius, so I know we are getting good coverage from the transmitter side of the repeater.

 

The duplexer has been tuned, we are using the proper jumpers for the duplexer, we are running 70 feet of 3/8" superflex andrew heliax. Brand new Comet antenna, etc. etc.

 

The only possibility I can seem to find through searching the internet is that there may be a bad jumper at the duplexer.

 

This setup was running at another site with no issues. The only thing that has changed is the feed line and the antenna.

 

 

 

 

Link to comment
Share on other sites

23 answers to this question

Recommended Posts

  • 0

I checked all the equipment last night to make sure it is all set for wideband operation.

 

When I was given the system the receive and transmit side of the duplexer needed to be re-connected, the rest were intact.

 

The duplexer is clearly labeled for receive and transmit. I can only assume it wasn't tuned backwards. Would you suggest swapping the two just in case or would that cause damage?

 

The antenna we have is a Comet CA-712EFC, the same antenna the prior operator used.

Link to comment
Share on other sites

  • 0

That is the same antenna that I'm running, although mine is fed with 60' of Comspec 1/2" heliax. Have you access to an antenna analyzer? If so, sweep the system at both your transmit and receive frequencies to see what the precise VSWR and impedance are.

Link to comment
Share on other sites

  • 0

I tuned the receiver to a frequency that transmits from about 3 towns away and my system received it loud and clear and passed it through to the transmitter with no issues.

 

I'm beginning to think that the terrain, current antenna height are working against me on the receive side. Wondering if its worth getting a receive preamp.

Link to comment
Share on other sites

  • 0

Ok the issue you're having could be one of several things so I'll break it down.

 

1: The radios you are using are not very well filtered and were never intended for duplex operation. The receiver may still be seeing the transmitter locally. Try bypassing the Henry amplifier and see how the performance of the system is.

 

2: Henry amplifiers suck and can be spurious. I have had dozens of them crap out over the years. Bypass the amplifier for now.

 

3. Have you performed a defense test? Have someone go out to a drop out location while you are in front of the repeater. Have them transmit and while they are talking. Shut off your repeater transmitter and see if the signal improves on the receiver.

 

4: What else is at your site? You may be fine internally to your repeater, however it does not sound as if you are utilizing any form of intermod protection (I.E. Isolator, circulator panel etc...) There may be some other repeater or transmitter that mixes with your transmitter and is causing inter-modulation which in turn would dramatically kill off your receive radio's sensitivity in full duplex mode.

 

RfMedic

Link to comment
Share on other sites

  • 0

I bypassed the Henry amp, set the transmit radio to high power & noticed no difference in regards to the issue I am having.

 

I have had people out in the field and I am able to receive them loud & clear with the transmitter off, turn the transmitter on & I lose their audio, but still receive the signal.

 

Nothing else is at my location that would cause any interference.

 

All the cabling for the duplexer is rg-214/u except for the output to the receiver & input from the amplifer.......those are lmr-400.

 

I know the rg-214/u is the proper cable to use between the duplexer cavities, antenna input, etc., but Is the LMR-400 ok to use for the receive & transmit sides of the duplexer? If not I'm guessing that could be the problem perhaps?

 

This system was given to me setup this way, so I am working through all the bugs myself.

 

Keep the feedback/tips coming!

 

Thanks

Link to comment
Share on other sites

  • 0

Honestly I suspect duplexer issues. Possibly in moving to a new location it was knocked out of tune. I bought a spectrum analyzer so I can tune duplexers, circulators, etc., but if you don't have one or access to one you'll need to carry it to a shop that can check the tuning.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Answer this question...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use and Guidelines.