justin10 Posted June 13 Report Share Posted June 13 20240612_213043.mp4 Quote Link to comment Share on other sites More sharing options...
OffRoaderX Posted June 13 Report Share Posted June 13 It is very difficult to tell from your horribly poor quality video, nor did you bother to mention it, but is that the new BTech repeater? If so, have you contacted BTech Support to see what they say about it? They have been very responsive when i had trouble with my BTech repeater. Raybestos and justin10 1 1 Quote Link to comment Share on other sites More sharing options...
WRKC935 Posted June 14 Report Share Posted June 14 That is some sort of ERROR beep. Could be low voltage feeding into unit, could be high SWR, could just be programmed wrong. I would check the manual, specifically the error codes and see if that sheds light on it. justin10 1 Quote Link to comment Share on other sites More sharing options...
justin10 Posted June 14 Author Report Share Posted June 14 Yes it is the btech and i contacted them they do not know what caused the noise but they are being very helpful sorry about the bad video hard to catch it in time it was very sporadic it has not happened since yesterday after reset and it's very possible that someone was playing it over a radio I bought mine the same time you got yours had to go back for repair same problem since receiving it back two weeks now it's working great. The cw I think still needs some fine tuning big fan I watch you all the time Quote Link to comment Share on other sites More sharing options...
justin10 Posted June 14 Author Report Share Posted June 14 Swr 1.1 and I went though and manually programed it there was no wattage loss or drop in the volt meter btech is still running test with my same settings and so far they can't duplicate problem Quote Link to comment Share on other sites More sharing options...
justin10 Posted June 14 Author Report Share Posted June 14 I would also think if it was a warning tone of some kind they would know what it was Quote Link to comment Share on other sites More sharing options...
WSBR383 Posted June 18 Report Share Posted June 18 (edited) Are you connected to a DC power supply? If so, and it is not adjustable, it needs to be exactly 12v, not 13.8v. I think they just updated that in their marketing information. Could that have been the cause? Edited June 18 by WSBR383 Quote Link to comment Share on other sites More sharing options...
justin10 Posted June 18 Author Report Share Posted June 18 Ac power Quote Link to comment Share on other sites More sharing options...
dosw Posted June 18 Report Share Posted June 18 5 hours ago, justin10 said: Ac power Why does your poor quality video show a DC power supply, then? This is what is shown in the video: https://www.amazon.com/Pyramid-PS9KX-Universal-Regulated-Converter/dp/B0002BA570?th=1 That's a DC power supply, supplying DC power from the AC mains. But to respond to @WSBR383, that power supply is 13.8v, which is outside of the specs he showed us for the GMRS-RPT50. So something that @justin10 hasn't grokked yet is that he's powering the repeater 1.3v above its specified input voltage range. I rather doubt that matters so much, but it is one thing to consider. Does the problem go away if you hook it directly up to a 12v battery? Quote Link to comment Share on other sites More sharing options...
gortex2 Posted June 18 Report Share Posted June 18 Uh...Id be more concerned with the 5AMP max supply andn ot the 13.8 volts. 13.8 is well within spec for a radio. Quote Link to comment Share on other sites More sharing options...
SteveShannon Posted June 18 Report Share Posted June 18 6 hours ago, WSBR383 said: Are you connected to a DC power supply? If so, and it is not adjustable, it needs to be exactly 12v, not 13.8v. I think they just updated that in their marketing information. Could that have been the cause? 1 minute ago, gortex2 said: Uh...Id be more concerned with the 5AMP max supply andn ot the 13.8 volts. 13.8 is well within spec for a radio. You missed the previous post which explains the voltage limitations of the duplexer (??) I don’t understand the limit. The duplexers I’m aware of are not powered. Quote Link to comment Share on other sites More sharing options...
justin10 Posted June 18 Author Report Share Posted June 18 So i will be little more clear the repeater is using ac plugged power no power supply other then what is internal the one you see in the video is powering the watt swr meter only Quote Link to comment Share on other sites More sharing options...
justin10 Posted June 18 Author Report Share Posted June 18 The bulit in power supply shows factory volts on display 11.8 volts witch is in spec for the repeater not a power issue it puts out 45 to 50 watts with no drop while in use even when the noise happened so I don't the the amps or volts is the problem beginning to think it was some kind of keyup from a radio it hasn't happened again since that knight but I also shut down the cw at the 15min mark moved to 20min so it could be a clich in the cw software more testing is need a this point was really just wonder if the noise had been heard before I know the video is bad but you work with what you can Thanks everyone Quote Link to comment Share on other sites More sharing options...
justin10 Posted June 18 Author Report Share Posted June 18 2 minutes ago, justin10 said: The bulit in power supply shows factory volts on display 11.8 volts witch is in spec for the repeater not a power issue it puts out 45 to 50 watts with no drop while in use even when the noise happened so I don't the the amps or volts is the problem beginning to think it was some kind of keyup from a radio it hasn't happened again since that knight but I also shut down the cw at the 15min mark moved to 20min so it could be a clich in the cw software more testing is need a this point was really just wonder if the noise had been healed before I know the video is bad but you work with what you can Thanks everyone Heared Quote Link to comment Share on other sites More sharing options...
WSBR383 Posted June 18 Report Share Posted June 18 4 minutes ago, justin10 said: The bulit in power supply shows factory volts on display 11.8 volts witch is in spec for the repeater not a power issue it puts out 45 to 50 watts with no drop while in use even when the noise happened so I don't the the amps or volts is the problem beginning to think it was some kind of keyup from a radio it hasn't happened again since that knight but I also shut down the cw at the 15min mark moved to 20min so it could be a clich in the cw software more testing is need a this point was really just wonder if the noise had been healed before I know the video is bad but you work with what you can Thanks everyone Well that is good, can eliminate that. I just wasn't sure if you were powering it with that DC power supply and thought that could be a potential issue. Put another handheld on the same receive frequency as the repeater and see if that is having those random noises as well, troubleshooting is eliminating potential issues. Another thing I would try is to try another power supply for your SWR meter or something that doesn't require power to eliminate some type of failure there as well. And like you said, change the CW and monitor, to get to the root of the problem. Good luck and hopefully you will find it and post the results to help the next guy/gal with a solution if they ever have that problem. Quote Link to comment Share on other sites More sharing options...
justin10 Posted June 18 Author Report Share Posted June 18 I will continue the hunt when problem is found I will let everybody now Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.