Albums
-
Misc. Radio Gear
I have a few Motorola radios. The XPR6550 is a good choice. You can buy them for reasonable prices. They also use a standard SMA type antenna connector. The XPR7550 is a better radio, but they are expensive used and have a funky stud type antenna port. So, if you need to use an external antenna you want the XPR6550.
- Album created by Lscott
- Updated
- 57 images
- 1 album comment
- 22 image comments
- 57 images
- 1 album comment
- 22 image comments
-
-
-
My GMRS radios and related gear
- Album created by WRNU354
- Updated
- 14 images
- 2 album comments
- 3 image comments
- 14 images
- 2 album comments
- 3 image comments
-
rough coverage maps
these are general Transmit coverages- Album created by JohnE
- Updated
- 2 images
- 2 images
-
Original WTC - Tower 1 - from 1,362' on the roof
A few personal photos from when I was an Electromagnetic Spectrum Authority and lived in NYC. I was one of the few people that had carte blanche access to almost any rooftop or tower in the country. Some of my other favorite skyscrapers in NYC for radio communications (roof tops that I also managed) were:
Citicorp Center WHQ - 153 E 53rd St. - 915' AGL
Chase Manhattan Bank WHQ - 1 Pine St. - 853' AGL
Chemical Bank WHQ - 270 Park Ave. - 747' AGL
The GM Building - 767 Fifth Ave. - 705' AGL
Citicorp Court Square - 2501 Jackson Ave - 685' AGL
One New York Plaza - 1 South St. - 630' AGL
The New York Palace - 455 Madison Ave. - 593' AGL
Confucious Plaza - 33 Bowery - 460' AGL
- Album created by rich2741
- 0 images
- 0 images
-
-
Under-canopy Headache Rack Ground Plane
When outfitting my 2015 Nissan Frontier I wasn't interested in putting visible antennas and drilling holes in the factory sheet metal. Since the truck is equipped with a tall fiberglass canopy ("camper shell") I decided to basically use the canopy a a poor man's radome. Took an old headache rack from a smaller truck, modified it to fit within the shell and to accommodate a pair of modded telco rack shelves to serve as ground planes.
I went with a sheet metal mount, drilled a 3/4" hole in the rack shelf as far forward as I could with the angle of the fiberglass canopy. It's a bit more aft than I would like but I can always fabricate an extension for the shelf by cutting up a second shelf, or possibly make something to go between the two separate shelves to extend the ground plane.
To get the cable to the radio I used a factory plugged hole in the forward wall of the bed, through a hole drilled in the plastic cabin pressure vent (so the vent remains functional, didn't just push through the vent) and I pulled the unterminated cable through, and soldered on a PL-259 connector.
- Album created by WRXN668
- Updated
- 16 images
- 1 album comment
- 16 images
- 1 album comment
-
-
-
JEEP GRMS Install
What my install of the Midland MXT 400 and Magellan GPSr looks like on the dash of my 2015 JK Hard Rock- Album created by H8SPVMT
- Updated
- 2 images
- 3 album comments
- 2 images
- 3 album comments
-
AI created open source- Radio related Images
These images I created with deep AI, I started trying to make a profile picture and before I knew it hours had passed and I climbed out of the rabbit hole with some images that have to be useful for something..
- Album created by DirtyCitizen
- Updated
- 12 images
- 12 images
-
-
WRDD287/KC3NSR
- Album created by kidphc
- Updated
- 18 images
- 2 image comments
- 18 images
- 2 image comments
-
-
My Stuff So Far :)
- Album created by TheNevilleKid
- Updated
- 2 images
- 3 image comments
- 2 images
- 3 image comments
-
-
CREST Communications
My participation in the Citizen Radio Emergency Service Team (CREST) in California.
- Album created by WQIR250
- Updated
- 34 images
- 34 images
-
-
Remote operations
Picture taken while hiking and using various homemade antennas and such for hitting the repeaters.
- Album created by WRUS730
- Updated
- 2 images
- 2 images