Jump to content

All Activity

This stream auto-updates

  1. Past hour
  2. I they are a member here you can message them by clicking on their avatar and clicking the "Message" icon.
  3. I need to contact an owner of a repeater and all I know is their Call Sign . Is there a way to do that on here?
  4. As I was referring to the "R" and "Q" model radio, those radios are Motorola radios. The Kenwood TK880 model (25 watt) band splits are: the TK880-1 is 450-490 MHz; TK880-2 is 485-512 MHz; TK880-3 is 400-430 MHz and the TK880H is the 40 watt radio with the same respective band splits. As Lscott said, you may be able to push the 70cm freq programming in the Kenwood. Since, I am not an Amateur, as in HAM radio operator, I never had a need to try that with my Kenwood.
  5. I just installed a Cobra 75 All Road in my SUV. I like it! I bought the BlueParrott B450-XT headset to go with it. I set the BlueParrott button to be the PTT for the Cobra and it works great. Audio from the Cobra using the BlueParrott mic sounds almost exactly the same as using the Cobra mic. Now I can use the Cobra without having to pick up the mic, and a big bonus is that there is no need for an external speaker. It works great.
  6. For a db or two that's true for most people. With a modest gain antenna the coax loses can be compensated for. For people on the very fringe of a coverage zone every db counts.
  7. I've heard that people in some areas in the East Valley are fortunate to hear both the 650 and 725 repeaters along with Pinal. We're not that fortunate here in the West Valley for the Two Tucson and Pinal repeaters. Since, the Pinal Repeater requires PT-T ID to access the repeater do you hear the ID squawking? I haven't been within range of Pinal since the change. I'm just curious if you can hear the squawking on keyup?
  8. You have to be careful about which models to get. For example the Kenwood TK-3180's come in two different band splits. Both will cover GMRS, but only one has Part 95A certification. The 450-520 MHz band split can be "pushed", enter out of band frequencies with a warning message, down below 450 MHz to get into the repeater section of the Ham 70cm band. https://forums.mygmrs.com/gallery/image/417-tk-2180jpg/?context=new Some radios, like the Motorola's, the frequency range is locked to the official one and out of band frequencies can't be entered like with the Kenwood's. You have to buy the correct band split version. Also they may not have Part 95 certification either. https://forums.mygmrs.com/gallery/image/261-motorola-xpr6550jpeg/ For example while the Motorola XPR6550 is a nice radio it's not FCC Part 95 certified. TK-3180 FCC Grant-2.pdf TK-3180 FCC Grant-1.pdf TK-2180_3180 Brochure-2.pdf XPR6550 FCC Grant 4.pdf XPR6550 FCC Grant 3.pdf XPR6550 FCC Grant 2.pdf
  9. I got a new repeater a few days ago and started pricing hardline for the new setup... it's going to cost me about $1,300 for 250 feet and a couple of connectors. I only paid $350 for the repeater. It's wild... but if you want it to work...
  10. Today
  11. With my K40 on my Pickup I think I am seeing between 3.4 and 3.7 with my Cobra 29 LTD Nightwatch depending on the selected channel, and my Firestik II antenna on my Jeep with my Cobra 19 DX III is seeing about 2.8 to 3.1 depending on the selected channel. The power levels were checked with the engine running. I'm still waiting to come across someone with a FM CB Radio so I can see how FM 29 LTD performs.
  12. As well as using the link tone on Shaw Butte, which will open the link to Towers 600, Diamond Point 575, and a couple others. Also, getting in with SWCRS gets access to Pinal 675, which has amazing coverage here as well. I haven't heard much off the Lemmon 650, but there's also the webhiway_tucson repeater that has a massive coverage area.
  13. And Shaw Butte. If you're a member of the Arizona GMRS Repeater Club, you would have access to the White Tanks Repeater which is linked to the Scottsdale, East Mesa, and Flagstaff repeaters.
  14. It's just 1 dB, not significant and you won't know the difference in the operating distance unless you buy your cable from Amazon.
  15. I think LMR600 has lower loses, a bit larger than LMR400, and I think it's not much more expensive either. The loss at 450MHz for LMR400 is 2.7db/100 feet. The loss at 450MHz for LMR600 is 1.7db/100 feet. For somebody who needs to run between 50 to 100 feed of coax stepping up to LMR600 would makes sense. The chart frequency of 450MHz is close enough to GMRS at 462/467 MHz the extra loss at the slightly higher frequency isn't that significant. For 50 feet of LMR400 at 450 MHz the power loss would be about 27%. For 50 feet of LMR600 at 450 MHz the power loss would be about 18%.
  16. I thought that my Kenwood TK880-1 would be compliant on the 462 MHz Interstitial channels on low power but my recertified Bird 43 says it puts out a tad over 6 watts. I remember that my POS MFJ 849 said 4.7 watts last year that is why I decided to check this morning to see what the Bird would said. As for operating on the 462 MHz Interstitial Channels, you can operate wideband and narrowband, its your discretion. It's not just narrowband only, as per Section/Rule Part 95.1771(a) The Kenwood and Motorola portables and mobiles would be your best bet in order to be compliant with Part 95, Subparts A and E, and have the ability to program 70cm freqs. You will need to find the "R" model radio in the earlier models and the "Q" model radios for the later models in order to have the operating band range for programming the 70cm and GMRS freqs.
  17. At a reasonable cost. There is better cable, various types of "hard line", but gets expensive real fast.
  18. A friend con me in going to the HAM thing at DeVry University with him this Saturday and if you or your friend is going to this HAM thing I can bring the 269D with me and give to you or him. Let me know if that will work.
  19. Use a handheld connected to a base antenna in the 2nd story window. 5W gets to the 20 mile repeater just fine. Once I tried the low power setting, which is 1/2W. It still got through but they said it was a bit scratchy.
  20. Thank you @Sshannon That is exactly the info I need.
  21. I’ve never had this problem however clear vinyl wrap would work best.
  22. I actually have a full sized CB radio in my car, and a 3' fiberglass antenna popping out of my roof. I've daily driven my car like that for the past 8 months actually haha
  23. I'm jumping up and down giggling right now after opening your Pcalifornia.kmz file in google earth. My god this is better than I expected, and color coded for open repeaters. How did you compile this data? Do you work for mygmrs? I like the idea of having a kmz file for each individual state, also having a kmz file is better too. I use a offline maps platform called osmand which is ridiculously powerful and incredibly feature and rich, and nearly every single option, map display, etc is customizable. And it's all offline. With this KMZ I can import it into that so while I am navigating I'll be able to see the repeaters nearby visually, something you cannot do in something like google maps or waze. I'm just awestruck because this has absolutely exceeded what I thought of being able to do. If there was a (free) or "pro" paid feature in the mygmrs app or website where you can download the kmz file database by state, and it's updated and recompiled the same way the app and map feature is, it's something I'd pay for, and maybe a few others as well. Very interesting. Thank you for your insight! Wow this thread has blown up a little, I'm glad this is getting some attention and stirring up some ideas among all of us Thank you everyone!
  24. You could save some money and use a lower powered radio. Wont need as big of a battery or a higher wattage solar panel. For instance my recent simplex repeater build has been running for a few weeks now on a measly 6ah battery and 10 watt solar panel. However my radio only draws 1.5 amps at 10 watts while transmitting, and .3 amps when idle. Here is the link if you want to see what i used and how it turned out. Might help give you some ideas.
  25. I can’t answer your question. However, it took watching several YouTube videos for me to get my head into the right space/perspective to successfully use the channel wizard. Once I arrived, it was easy. Hang in there. YOU CAN DO IT!
  1. Load more activity
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use and Guidelines.